1997-2001 Honda CR-V 2.0L L4 | 2 PC Rear Wheel Bearing | OE#42210S10000/512240 - PHILTOP

1997-2001 Honda CR-V 2.0L L4 | 2 PC Rear Wheel Bearing | OE#42210S10000/512240 - PHILTOP

Triple-Lip Seal

Rear

AISI 52100

4.9

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
1527WBR3487US

Specifications

Brand
PHILTOP
Position
Rear
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Rear Wheel Hub and Bearing Assembly - 512166/512240,Installation Instructions
Surface Finish
Polished, Rust Protected
Warranty Period
2-Year
OE Number
42210S10000,42210S10A10,42210S10A00,42200S10A01,42201S10A01,44600S47000
Part Number
512240,512166,HA592210,712240,7350133,40540015,40540014E,40540014,WE60536,H512240,H512166,0516277,0514235,712166,BR930434,BR930444,7350350,NT512240,VKBA6857,NT512166,WE60535,40540015E,RW8240,VKBA6858,HUB1894,RW8166,HUB189,HUB1892
Quantity
2

Highlights

  • Wide Compatibility: PHILTOP Wheel Bearing and Hub Assembly fit for 2004-2017 Toyota Camry, 2007-2014 Ford Edge, 2004-2010 Toyota Sienna, 2007-2018 Lexus ES350, 2005-2018 Toyota Avalon, 2001-2007 Toyota Highlander, 2007-2018 Mazda CX-9, 2009-2015 Toyota Venza, 2007-2015 Lincoln MKX, 2004-2008 Toyota Solara, 2004-2006 Lexus ES330, 2007-2009 Lexus RX350 AWD, 2007-2012 Mazda CX-7, 2004-2006 Lexus RX330 AWD, 2007-2009 Lexus RX350 FWD, 2004-2006 Lexus RX330 FWD, 2013-2018 Lexus ES300h, 2006-2008 Lexus RX400h, 2009-2013 Toyota Matrix, 2009-2010 Pontiac Vibe, 2006-2007 Mazda 6 AWD.
  • Outstanding Quality: Wheel bearings are manufactured in accordance with the quality standards of the original manufacturer. Our careful selection of materials and excellent manufacturing process create excellent wheel bearings.
  • Tips: Before purchasing wheel bearings, it is essential to verify that the wheel hub assembly is suitable for your vehicle.
  • Long Service life: Wheel bearings are characterized by good resistance to wear, corrosion and aging. These characteristics maximize the strength and durability of the wheel hub.
  • Easy Installation: Wheel bearings are installed in place and fit the original car. Wheel bearings are easy to install, no drilling or modification required, convenient for you to replace at home.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year1998 - 20011997 - 20012000 - 2001
MakeHondaHondaHonda
ModelCR-VCR-VCR-V
TrimEXLXSE
Engine2.0L L42.0L L42.0L L4
Note---

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.9/5

Based on 66 reviews

589%
411%
30%
20%
10%

Customer photos and videos

DS

06/24/2026

Verified buyer

Exact replacement for my car. The threads were clean and spline too. Made assembly very easy.

CrypticCritic

01/25/2024

Verified buyer

I used these Philtop 512333 wheel bearings as part of a rebuild of a 2007 Jeep Patriot rear suspension. Everything fit as it was designed to. Bearings seem of good quality and at a reasonable value. I will update if I have any issues with them.

FAQS

Stop the installation and contact Philtop customer support. Please provide your vehicle information, order number and photos of the original and received parts so we can help review the fitment.

Package contents vary by part number. Please check the product images and specifications to confirm whether the hub, ABS sensor, axle nut, or other hardware is included.

A single bearing can often be replaced when only one side is worn. The condition of the bearing on the opposite side should also be checked because wear can vary by vehicle and use.