(Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 62.78 inch; ③Compressed Shaft Length: 60.41 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft; ⑧Mounting Type: Ball Cage + Ball Cage; ⑨Design: Two-Piece; ⑩Adjustable Length for Custom Fit
(High Quality)Made with durable forged steel and advanced alloy materials, it efficiently transmits torque while accommodating shaft movement under load Dynamic balancing before delivery guarantees a smooth, reliable ride
(Drive with Pleasure)PHILTOP makes driving a pleasure with safer, smoother components Our OEM-grade replacement driveshaft restores original performance and delivers a noticeably more comfortable ride
Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.
Installation Steps
Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
Step-7: Connect the rear flange and hand-start all bolts.
Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.
After Installation
Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.
Product Description
Reviews
5.0/5
Based on 2 reviews
5
100%
4
0%
3
0%
2
0%
1
0%
R
RickFixIt_106
03/13/2026
Got here quicker than I thought it would, which was awesome since my car was down. The packaging was solid, everything was secure. Had a quick question about torque specs and customer service answered it right away. Great service.
K
Kelly_SUV_Life_738
11/08/2025
Bolted right up to my CTS with no issues at all. I was a little worried about doing it myself, but it was surprisingly straightforward. Feels much smoother on the road now, and the price was way better than a local shop quoted.
FAQS
No FAQs have been added for this product yet.
Add your vehicle to ensure fitment
Make
Model
Trim
Engine
Loading vehicle options...
Choose Year, Make, and Model to check exact fitment.
(Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 62.78 inch; ③Compressed Shaft Length: 60.41 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft; ⑧Mounting Type: Ball Cage + Ball Cage; ⑨Design: Two-Piece; ⑩Adjustable Length for Custom Fit
(High Quality)Made with durable forged steel and advanced alloy materials, it efficiently transmits torque while accommodating shaft movement under load Dynamic balancing before delivery guarantees a smooth, reliable ride
(Drive with Pleasure)PHILTOP makes driving a pleasure with safer, smoother components Our OEM-grade replacement driveshaft restores original performance and delivers a noticeably more comfortable ride
Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.
Installation Steps
Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
Step-7: Connect the rear flange and hand-start all bolts.
Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.
After Installation
Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.
Product Description
Reviews
5.0/5
Based on 2 reviews
5
100%
4
0%
3
0%
2
0%
1
0%
R
RickFixIt_106
Mar 13,2026
Got here quicker than I thought it would, which was awesome since my car was down. The packaging was solid, everything was secure. Had a quick question about torque specs and customer service answered it right away. Great service.
K
Kelly_SUV_Life_738
Nov 08,2025
Bolted right up to my CTS with no issues at all. I was a little worried about doing it myself, but it was surprisingly straightforward. Feels much smoother on the road now, and the price was way better than a local shop quoted.