2002-2007 Jeep Liberty 3.7L V6 | Front Drive Shaft | 938123 - PHILTOP

2002-2007 Jeep Liberty 3.7L V6 | Front Drive Shaft | 938123 - PHILTOP

Front

Factory-Balanced

Corrosion-Resistant

4.8

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
86ISDSA1017US

Specifications

Brand
PHILTOP
Mounting Type
Cv Joint to Cv Joint
Position
Front
Fully Extended Length
32.48 in/825 mm
Fully Compressed Length
29.96 in/761 mm
Shaft Diameter
Φ51
Items Included
1x Drive Shaft - 938123
Surface Finish
Painted
Two-Piece Design
No
Adjustable Length
Yes
Tube Wall Thickness
0.12 in/3 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
938123

Highlights

  • (Vehicle Fitments)Fits for Jeep 2002-2007 Liberty 3.7L 4WD Manual(Conversion Shaft/Kit Includes New 32 Spline Transfer Case Yoke)
  • (Specifications)①Installation Position: Front Side; ②Extended Shaft Length: 32.48 inch; ③Compressed Shaft Length: 29.96 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ51; ⑥Shaft Wall Thickness: 0.118 inch; ⑦Length is measured end to end across the entire driveshaft
  • (Reference Number)938123,52111597AA
  • (Attention)①Mounting Type: Ball Cage + Ball Cage; ②Adjustable Length for Custom Fit; ③Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Quality-Controlled Manufacturing)Produced under monitored quality control from raw materials to final shipment, with inspections at each stage to support consistent performance and OEM design compliance

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2002 - 20062002 - 2007
MakeJeepJeep
ModelLibertyLiberty
TrimRenegadeSport
Engine3.7L V63.7L V6
Note
Conversion Shaft/Kit Includes New 32 Spline Transfer Case Yoke;w/Sales Code DHN (Command-Trac Part Time 4WD System)
Conversion Shaft/Kit Includes New 32 Spline Transfer Case Yoke;w/Sales Code DHN (Command-Trac Part Time 4WD System)

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.8/5

Based on 6 reviews

583%
417%
30%
20%
10%

CarGuy_John_602

11/17/2025

For the price, this drive shaft is a steal. It looks and feels like a premium part. I'm really impressed with the quality for what I paid.

Brad_AutoParts_22

01/01/2026

Super fast shipping, arrived in perfect condition. Packaging was really solid. I called with a question and the customer service rep was incredibly helpful. Great job all around!

FAQS

No FAQs have been added for this product yet.