1999-2001 Ford F-250 Super Duty 7.3L V8 | Front Drive Shaft | 938305 - PHILTOP

1999-2001 Ford F-250 Super Duty 7.3L V8 | Front Drive Shaft | 938305 - PHILTOP

Front

Factory-Balanced

Corrosion-Resistant

4.4

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
38ISDSA1317US

Specifications

Brand
PHILTOP
Mounting Type
Cv Joint to Cv Joint
Position
Front
Fully Extended Length
44.49 in/1130 mm
Fully Compressed Length
41.14 in/1045 mm
Shaft Diameter
Φ73
Items Included
1x Drive Shaft - 938305
Surface Finish
Painted
Flange Shape
Round
Bolt Hole Quantity
4
Two-Piece Design
No
Universal Joint Size
Φ30.18*92
Adjustable Length
Yes
Tube Wall Thickness
0.08 in/2 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
938305

Highlights

  • (Vehicle Fitments)Fits Ford 1999-2001 F-250 Super Duty 7.3L 4WD, 1999-2001 F-350 Super Duty 7.3L 4WD(w/Single Rear Wheel), 2000-2003 Excursion 7.3L 4WD(From 10/199)
  • (Specifications)①Installation Position: Front Side; ②Extended Shaft Length: 44.49 inch; ③Compressed Shaft Length: 41.14 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ73; ⑥Shaft Wall Thickness: 0.079 inch; ⑦U-Joint Size: φ30.18*92; ⑧Length is measured end to end across the entire driveshaft
  • (Reference Number)938305,F81Z4A376MA,5C3Z4A376D,YC3Z4A376EA
  • (Attention)①Mounting Type: Ball Cage + Ball Cage; ②Flange Type: Round; ③Adjustable Length for Custom Fit; ④Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Precisely Metered Pre-Lubrication) Each unit receives an engineering-determined quantity of grease before shipping. This metered application helps reduce the risk of under-lubrication or over-lubrication

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year200320002001 - 200320002001 - 20031999 - 20011999 - 20011999 - 20011999 - 20011999 - 20011999 - 2001
MakeFordFordFordFordFordFordFordFordFordFordFord
ModelExcursionExcursionExcursionExcursionExcursionF-250 Super DutyF-250 Super DutyF-250 Super DutyF-350 Super DutyF-350 Super DutyF-350 Super Duty
TrimEddie BauerLimitedLimitedXLTXLTLariatXLXLTLariatXLXLT
Engine7.3L V87.3L V87.3L V87.3L V87.3L V87.3L V87.3L V87.3L V87.3L V87.3L V87.3L V8
Note-
From 10/1999
-
From 10/1999
----
w/Single Rear Wheel (SRW)
w/Single Rear Wheel (SRW)
w/Single Rear Wheel (SRW)

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.4/5

Based on 5 reviews

560%
420%
320%
20%
10%

Steve_DIYer_353

12/20/2025

This installed way easier than I thought it would. Everything lined up perfectly, no problems at all. Definitely better than other driveshafts I've worked with.

Mike from Texas_56

11/20/2025

Was a little concerned about fitment, but this slid right into place. No issues whatsoever. Much easier install than the last drive shaft I bought.

FAQS

No FAQs have been added for this product yet.