(Vehicle Fitments)Fits Jeep 2011-2021 Grand Cherokee 3.6L AWD (Single Speed Transfer Case),for Dodge 2011-2013 Durango AWD (Single Speed Transfer Case), 2014-2025 Durango 3.6L AWD
(Specifications)①Installation Position: Front Side; ②Extended Shaft Length: 25.79 inch; ③Compressed Shaft Length: 23.43 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft
(Attention)①Mounting Type: Ball Cage + Ball Cage; ②Adjustable Length for Custom Fit; ③Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
(Professional Protective Packaging)A multi-layer protective wrap is applied to help absorb transit shocks and limit physical distortion
Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.
Installation Steps
Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
Step-7: Connect the rear flange and hand-start all bolts.
Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.
After Installation
Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.
Product Description
Reviews
4.8/5
Based on 4 reviews
5
75%
4
25%
3
0%
2
0%
1
0%
S
Snowflake
08/03/2026
Verified buyer
This front driveshaft was a good DIY replacement and fit my vehicle without any issues. The mounting points lined up correctly, and everything bolted into place as expected. After installation, the drivetrain felt much smoother, with the vibration and clunking I was experiencing gone. If you’re comfortable working underneath your vehicle, this is a solid replacement that gets the job done.
R
RickFixIt_388
04/03/2026
Got here super fast, like, surprisingly fast! The packaging was solid and kept everything safe. Plus, when I had a quick question, customer service was on point and super helpful. Great experience overall.
FAQS
No FAQs have been added for this product yet.
Add your vehicle to ensure fitment
Make
Model
Trim
Engine
Loading vehicle options...
Choose Year, Make, and Model to check exact fitment.
(Vehicle Fitments)Fits Jeep 2011-2021 Grand Cherokee 3.6L AWD (Single Speed Transfer Case),for Dodge 2011-2013 Durango AWD (Single Speed Transfer Case), 2014-2025 Durango 3.6L AWD
(Specifications)①Installation Position: Front Side; ②Extended Shaft Length: 25.79 inch; ③Compressed Shaft Length: 23.43 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft
(Attention)①Mounting Type: Ball Cage + Ball Cage; ②Adjustable Length for Custom Fit; ③Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
(Professional Protective Packaging)A multi-layer protective wrap is applied to help absorb transit shocks and limit physical distortion
Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.
Installation Steps
Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
Step-7: Connect the rear flange and hand-start all bolts.
Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.
After Installation
Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.
Product Description
Reviews
4.8/5
Based on 4 reviews
5
75%
4
25%
3
0%
2
0%
1
0%
S
Snowflake
Aug 03,2026
Verified buyer
This front driveshaft was a good DIY replacement and fit my vehicle without any issues. The mounting points lined up correctly, and everything bolted into place as expected. After installation, the drivetrain felt much smoother, with the vibration and clunking I was experiencing gone. If you’re comfortable working underneath your vehicle, this is a solid replacement that gets the job done.
R
RickFixIt_388
Apr 03,2026
Got here super fast, like, surprisingly fast! The packaging was solid and kept everything safe. Plus, when I had a quick question, customer service was on point and super helpful. Great experience overall.
FAQS
No FAQs have been added for this product yet.
2011-2025 Dodge Durango Front Drive Shaft 938267 | PHILTOP