2006-2010 Hummer H3 3.7L/5.3L/3.5L | Front Drive Shaft | 938008 - PHILTOP

2006-2010 Hummer H3 3.7L/5.3L/3.5L | Front Drive Shaft | 938008 - PHILTOP

Front

Factory-Balanced

Corrosion-Resistant

4.4

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
98ISDSA0877US

Specifications

Brand
PHILTOP
Mounting Type
Cv Joint + U-Joint
Position
Front
Fully Extended Length
31.61 in/803 mm
Fully Compressed Length
29.65 in/753 mm
Shaft Diameter
Φ51
Items Included
1x Drive Shaft - 938008
Surface Finish
Painted
Two-Piece Design
No
Universal Joint Size
Φ27*81.8
Adjustable Length
Yes
Tube Wall Thickness
0.12 in/3 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
938008

Highlights

  • (Vehicle Fitments)Fits for Hummer 2006-2010 H3, 2009-2010 H3T
  • (Specifications)①Installation Position: Front Side; ②Extended Shaft Length: 31.61 inch; ③Compressed Shaft Length: 29.64 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ51; ⑥Shaft Wall Thickness: 0.118 inch; ⑦U-Joint Size: Φ27*81.8; ⑧Length is measured end to end across the entire driveshaft
  • (Reference Number)938008,15878295,25840721,15860584,10376298,25859867
  • (Attention)①Mounting Type: Ball Cage + Universal Joint; ②Adjustable Length for Custom Fit; ③Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Quiet Operation Design)This product is built with precision bearings, superior grease, and exacting tolerance standards. The combination supports reduced noise output while driving

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2008 - 20092008 - 201020062007 - 201020092008 - 20092007 - 20092009 - 20102009 - 2010
MakeHummerHummerHummerHummerHummerHummerHummerHummerHummer
ModelH3H3H3H3H3H3H3H3TH3T
TrimAdventureAlphaBaseBaseChampionship SeriesLuxuryXAlphaBase
Engine3.7L L55.3L V83.5L L53.7L L55.3L V83.7L L53.7L L55.3L V83.7L L5
Note---------

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.4/5

Based on 7 reviews

557%
429%
314%
20%
10%

Kelly_SUV_Life_110

10/22/2025

Got here fast and was packaged well. Customer service was super helpful when I had a question about the torque specs.

Tom_Handy_528

11/22/2025

Arrived super fast, well packed. I called support just to double check something and they were really knowledgeable and friendly.

FAQS

No FAQs have been added for this product yet.

2006-2010 Hummer H3 Front Drive Shaft 938008 | PHILTOP