2002-2006 Dodge Ram 1500 3.7L V6/4.7L V8/5.7L V8/5.9L V8 | Front Drive Shaft | 938150 - PHILTOP

2002-2006 Dodge Ram 1500 3.7L V6/4.7L V8/5.7L V8/5.9L V8 | Front Drive Shaft | 938150 - PHILTOP

Front

Factory-Balanced

Corrosion-Resistant

4.5

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
64ISDSA1097US

Specifications

Brand
PHILTOP
Mounting Type
Cv Joint to Cv Joint
Position
Front
Fully Extended Length
32.76 in/832 mm
Fully Compressed Length
32.76 in/832 mm
Shaft Diameter
Φ63.5
Items Included
1x Drive Shaft - 938150
Surface Finish
Painted
Flange Shape
Square
Output Shaft Spline Count
30T
Bolt Hole Quantity
4
Two-Piece Design
No
Adjustable Length
No
Tube Wall Thickness
0.08 in/2 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
938150

Highlights

  • (Vehicle Fitments)Fits for Dodge 2002-2005 Ram 1500 4WD Automatic, 2006 Ram 1500 4WD Extended/Standard Cab Automatic
  • (Specifications)①Installation Position: Front Side; ②Extended Shaft Length: 32.75 inch; ③Compressed Shaft Length: 32.75 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft
  • (Reference Number)938150,52123021AB,52123021AA,52105990AB,52123021AC,52105990AA
  • (Attention)①Mounting Type: Ball Cage + Ball Cage; ②Flange Type: Square;
  • (Precisely Metered Pre-Lubrication) Each unit receives an engineering-determined quantity of grease before shipping. This metered application helps reduce the risk of under-lubrication or over-lubrication

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year20032003 - 200420062003 - 200620032002 - 20032002 - 20062003 - 20062002 - 20032002 - 20062002 - 20062003 - 20062002 - 2003200620062006
MakeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodge
ModelRam 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500
TrimLaramieLaramieLaramieLaramieLaramieSLTSLTSLTSLTSTSTSTSTSportTRX4TRX4
Engine3.7L V64.7L V84.7L V85.7L V85.9L V83.7L V64.7L V85.7L V85.9L V83.7L V64.7L V85.7L V85.9L V85.7L V84.7L V85.7L V8
Note----------------

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.5/5

Based on 6 reviews

567%
417%
317%
20%
10%

Emma_DailyCommute_857

01/27/2026

Looks great, feels really solid. The finish is nice and it seems like it'll hold up well. Fantastic price for this kind of quality.

Chris_GearHead_767

03/01/2026

Came packaged really well, and it got here super fast. I had a quick question for customer service and they were great, very knowledgeable.

FAQS

No FAQs have been added for this product yet.