2007-2011 Jeep Wrangler 3.8L V6 | Front Drive Shaft | 938102 - PHILTOP

2007-2011 Jeep Wrangler 3.8L V6 | Front Drive Shaft | 938102 - PHILTOP

Front

Factory-Balanced

Corrosion-Resistant

5.0

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
55ISDSA1007US

Specifications

Brand
PHILTOP
Position
Front
Items Included
1x Drive Shaft - 938102
Two-Piece Design
No
Adjustable Length
Yes
Shaft Material
Steel
Warranty Period
2-Year
Part Number
938102

Highlights

  • (Vehicle Fitments)Fits for Jeep 2007-2011 Wrangler 4WD(0 to 6 In. Lift; Conversion Shaft)
  • (Specifications)①Installation Position: Front Side; ②Shaft Material: Steel; ③Length is measured end to end across the entire driveshaft
  • (Reference Number)938102,52853317AE,52853317AD,52753319AC,52853317AC,52853317AB,52853317AA,52853321AC
  • (Attention)①Adjustable Length for Custom Fit; ②Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Comprehensive Quality Control)Material selection begins the process, and quality checks continue through every production stage until final packaging. These routine procedures help maintain even product quality and support design standards aligned with OEM specifications

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year20112007 - 20112007 - 20112010 - 201120112007 - 20112007 - 20112010 - 20112007 - 20102007 - 2010
MakeJeepJeepJeepJeepJeepJeepJeepJeepJeepJeep
ModelWranglerWranglerWranglerWranglerWranglerWranglerWranglerWranglerWranglerWrangler
Trim70th AnniversaryRubiconSaharaSportUnlimited 70th AnniversaryUnlimited RubiconUnlimited SaharaUnlimited SportUnlimited XX
Engine3.8L V63.8L V63.8L V63.8L V63.8L V63.8L V63.8L V63.8L V63.8L V63.8L V6
Note
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft
0 to 6 In. Lift;Conversion Shaft

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

5.0/5

Based on 3 reviews

5100%
40%
30%
20%
10%

CarGuy_John_261

11/27/2025

This thing looks fantastic and feels really solid. Definitely a great bang for your buck. Highly recommend this if you need a replacement.

Nancy_FirstCar_210

11/09/2025

Installation was a breeze, everything lined up perfectly. No issues whatsoever. Feels much more robust than the original part.

FAQS

No FAQs have been added for this product yet.

2007-2011 Jeep Wrangler Front Drive Shaft 938102 | PHILTOP