2008-2012 Jeep Liberty 3.7L V6 | Front Drive Shaft | 938171 - PHILTOP

2008-2012 Jeep Liberty 3.7L V6 | Front Drive Shaft | 938171 - PHILTOP

Front

Factory-Balanced

Corrosion-Resistant

5.0

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
50ISDSA1147US

Specifications

Brand
PHILTOP
Mounting Type
Cv Joint to Cv Joint
Position
Front
Fully Extended Length
32.48 in/825 mm
Fully Compressed Length
30.43 in/773 mm
Shaft Diameter
Φ51
Items Included
1x Drive Shaft - 938171
Surface Finish
Painted
Flange Shape
Square
Bolt Hole Quantity
4
Two-Piece Design
No
Adjustable Length
Yes
Tube Wall Thickness
0.12 in/3 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
938171

Highlights

  • (Vehicle Fitments)Fits for 2008-2012 Jeep Liberty 3.7L 4WD, Front position. Please verify your vehicle's year, model, and configuration carefully before purchasing
  • (OE Reference)OE 938171, 52853442AD, 52853442AC, 52853442AF, 52853442AE. Manufactured to meet original factory specifications for a reliable direct replacement
  • (Product Specifications)①Installation Position: Front; ②Extended Shaft Length: 32.48 inch; ③Compressed Shaft Length: 30.43 inch; ④Shaft Material: Steel; ⑤Shaft Wall Thickness: 3mm; ⑥Shaft Diameter: 51mm; ⑦Length Adjustable: Yes; ⑧Installation Type: CV Joint + CV Joint; ⑨Flange Type: Square
  • (Quality & Durability)Built with high-quality steel and precision engineering for lasting performance. Designed to withstand demanding driving conditions and deliver dependable service over the long term
  • (Noise-Free Operation)Engineered for smooth, quiet performance. Precision-balanced construction helps minimize vibration and noise for a comfortable, refined driving experience

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year20122008 - 20122010 - 20112008 - 2012
MakeJeepJeepJeepJeep
ModelLibertyLibertyLibertyLiberty
TrimJetLimitedRenegadeSport
Engine3.7L V63.7L V63.7L V63.7L V6
Note----

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

5.0/5

Based on 1 review

5100%
40%
30%
20%
10%

Rock

07/27/2026

Verified buyer

This front drive shaft for the Jeep Liberty is good. Some listing reviews were for something else so guess things changed, but we got what we ordered.Build quality is solid with good rust protection. Durable and smooth after installation. Runs quietly and smoothly as the vehicle drives around. No issues at all.Price is reasonable so a good deal. Recommended.

FAQS

No FAQs have been added for this product yet.