2001-2005 Honda Civic 1.7L | 2 PC Rear Wheel Bearing | 42200S5A008/512175 - PHILTOP

2001-2005 Honda Civic 1.7L | 2 PC Rear Wheel Bearing | 42200S5A008/512175 - PHILTOP

Triple-Lip Seal

Rear

AISI 52100

4.6

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
1066WBK353XUS

Specifications

Brand
PHILTOP
ABS Type
Tone Ring
Lug Count
4
Position
Rear
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Rear Wheel Hub and Bearing Assembly - 512175,Installation Instructions
Bolt Pattern
4x4.0
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
2.6 in
Flange Offset
2.2 in/56 mm
Flange Diameter
5.47 in/139.0 mm
Brake Pilot Diameter
2.4 in/61.0 mm
Warranty Period
2-Year
OE Number
42200S5A008,42200S5A0080
Part Number
512175,40640023,0516275,H512175,7350109,712175,0516300,NT512175,WE60560,BR930255,VKBA6839,40640023E,RW8175,BR930381,G512175,HUB22723P,HUB22723
Quantity
2

Highlights

  • Compatibility: Rear Wheel Bearing and Hub Assembly for 2001-2005 Civic.
  • Wheel Hub Num: 512175, NT512175, 42200S5A008, H512175, 7350109, BR930255, VKBA6839, 0516275, WE60560, 712175, 40640023, 0516300, WA512175, 29512175, 40640023E, RW8175, 516300, 516275, G512175, 102087, 141104413, 213175.
  • Superior Quality: Our wheel hubs are made of high quality materials and have the same performance as the original equipment. In addition, the wheel bearing hub assembly is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • Recovery Performance: Wheel bearings support the gravity of the entire body and precisely guide the wheel rotation. High-quality wheel hub assemblies allow you to drive your vehicle safely and smoothly.
  • Please Note: If you do not have an installation manual or are not skilled enough to install wheel bearings, it is recommended that you seek assistance from a qualified mechanic.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2001 - 20032004 - 20052004 - 2005
MakeHondaHondaHonda
ModelCivicCivicCivic
TrimEXEXGX
Engine1.7L L41.7L L41.7L L4
Note-
4-Wheel ABS
4-Wheel ABS

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

PHILTOPPT

Reviews

4.6/5

Based on 7 reviews

571%
414%
314%
20%
10%

Brad_AutoParts_830

02/28/2026

Arrived super fast, way ahead of schedule. Installation was incredibly easy, literally took minutes. Fit my Civic like a glove. Couldn't be happier.

RickFixIt_53

12/30/2025

This fixed the awful grinding sound I was hearing from the rear. My Civic feels so much more stable and safe to drive now. A huge improvement over the old ones.

FAQS

Please provide your order number, vehicle information, installation date, current mileage and a description of the issue. Photos, videos or inspection information may also help us review the claim.

A single bearing can often be replaced when only one side is worn. The condition of the bearing on the opposite side should also be checked because wear can vary by vehicle and use.

The design depends on the application. Compare the product type and images with the original part before installation; press-in bearings generally require suitable shop tools.