2003-2011 Honda Element 2.4L L4 | 2 PC Rear Wheel Bearing | OE#42200SCVA11/512262 - PHILTOP

2003-2011 Honda Element 2.4L L4 | 2 PC Rear Wheel Bearing | OE#42200SCVA11/512262 - PHILTOP

Triple-Lip Seal

Rear

AISI 52100

4.8

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
9919WBR3438US

Specifications

Brand
PHILTOP
ABS Type
Magnetic Ring
Position
Rear
Flange Bolt Hole Count
6
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Rear Wheel Hub and Bearing Assembly - 512262/512263,Installation Instructions
Surface Finish
Polished, Rust Protected
Warranty Period
2-Year
OE Number
42200SCVA11,42201SCVA12,42200SCVA31
Part Number
512262,512263,BM500014,BM500003,40540016,40540018,WE60582,WE60583,40540018E,BR930319,BR930619,BM500002,0514260,712262,0514245,712263,HUB287,NT512262,7460245,NT512263,H512262,H512263,PBR930398,40540017,0514246,PT512263,363260,141109837,7350370,102509,102510,141109840,RW8263,363262,RW8262,40540016E,HUB28717,HUB2872,HUB28716
Quantity
2

Highlights

  • Compatibility: Rear Left Wheel Bearing and Hub Assembly for 2003-2011 Honda Element.
  • Wheel Hub Num: 512262, 42201SCVA12, BR930319, BM500014, NT512262, BM500003, 0514260, 40540016, 712262, PBR930398, BM500000, BM500002, HUB287, 512260, 42200SCVA02, H512262, BR930496, 40540017, 42200SCVA01, 40540017E, H512260, RW8260, HUB2878, WE60584, 514260.
  • Superior Quality: Our wheel hubs are made of high quality materials and have the same performance as the original equipment. In addition, the wheel bearing hub assembly is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • Recovery Performance: Wheel bearings support the gravity of the entire body and precisely guide the wheel rotation. High-quality wheel hub assemblies allow you to drive your vehicle safely and smoothly.
  • Please Note: If you do not have an installation manual or are not skilled enough to install wheel bearings, it is recommended that you seek assistance from a qualified mechanic.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2003 - 20112006 - 20112007 - 2010
MakeHondaHondaHonda
ModelElementElementElement
TrimEXLXSC
Engine2.4L L42.4L L42.4L L4
Note---

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

PHILTOPPT

Reviews

4.8/5

Based on 6 reviews

583%
417%
30%
20%
10%

Kelly_SUV_Life_418

02/02/2026

Solid construction and a great price point. My Element's rear is running smooth and quiet again. You can tell it's a well-made part.

Lisa_CivicDriver_281

02/27/2026

Came really fast and fit my Element like a charm. Installation was a breeze, no issues at all. Happy with the quick service.

FAQS

Stop the installation and contact Philtop customer support. Please provide your vehicle information, order number and photos of the original and received parts so we can help review the fitment.

Noise may come from another wheel bearing, the tire, brake, CV joint, or an installation issue. Recheck the installation and inspect nearby components before assuming the new bearing is faulty.

Keep the part clean, avoid impact through the rolling elements, use the correct pressing surface, and tighten fasteners to the specified torque. Professional installation is recommended if special tools are required.