2004-2006 Lexus RX330 3.3L | 1 PC Rear FWD Wheel Bearing | 4246000000000000/512282 - PHILTOP

2004-2006 Lexus RX330 3.3L | 1 PC Rear FWD Wheel Bearing | 4246000000000000/512282 - PHILTOP

Triple-Lip Seal

Rear

FWD

4.0

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
8434WBK379HUS

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Drive Type
FWD
Lug Count
5
Position
Rear
Flange Bolt Hole Count
4
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
1x Rear Wheel Hub and Bearing Assembly - 512282,Installation Instructions
Bolt Pattern
5 X 4.5
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
3.3 in
Wheel Stud Size
M12x1.5
Flange Offset
2.83 in/72 mm
Flange Diameter
5.98 in/151.9 mm
Brake Pilot Diameter
2.44 in/62.0 mm
Warranty Period
2-Year
OE Number
4246000000000000,4250000000000000,424615,425E17,4246048030,425E15
Part Number
512282,HA592461,7700347,WE61058,40744003,BR930376,NT512282,712282,0516101,WA512282,693282,H512282,29512282,WH512282,PBR930615,40744003E,PT512282,102112,141102442,P512282,PM512282,RW8282,3DACF033F5AS
Quantity
1

Highlights

  • Compatibility: Rear Left Wheel Bearing and Hub Assembly for 2004-2007 Highlander FWD, 2007-2009 RX350 FWD, 2004-2006 RX330 FWD, 2006-2008 RX400h FWD.
  • Wheel Hub Num: 512282, NT512282, BR930376, HA592461. Please refer to the Vehicle menu at the top of the list, select your vehicle's "Year, Make, Model" and click "Confirm" to make sure the wheel bearing fit your car.
  • Superior Quality: Our wheel hubs are made of high quality materials and have the same performance as the original equipment. In addition, the wheel bearing hub assembly is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • Recovery Performance: Wheel bearings support the gravity of the entire body and precisely guide the wheel rotation. High-quality wheel hub assemblies allow you to drive your vehicle safely and smoothly.
  • Please Note: If you do not have an installation manual or are not skilled enough to install wheel bearings, it is recommended that you seek assistance from a qualified mechanic.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2004 - 20062007 - 200820092006 - 20082004 - 20072004 - 20072006 - 20072006 - 20072005 - 20072006 - 2007
MakeLexusLexusLexusLexusToyotaToyotaToyotaToyotaToyotaToyota
ModelRX330RX350RX350RX400hHighlanderHighlanderHighlanderHighlanderHighlanderHighlander
TrimBaseBaseBaseBaseBaseBaseHybridHybrid LimitedLimitedSport
Engine3.3L V63.5L V63.5L V63.3L V62.4L L43.3L V63.3L V63.3L V63.3L V63.3L V6
Note
Four-Wheel Drive
Four-Wheel Drive;Non Japan Built
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

PHILTOPPT

Reviews

4.0/5

Based on 3 reviews

533%
433%
333%
20%
10%

Jason_Trucks_770

04/14/2026

I was pleasantly surprised by the quality of this bearing. It feels very robust and well-constructed. Definitely a great bang for your buck.

Mike from Texas_665

11/24/2025

The part arrived, but it was a day later than the tracking said it would be. It installed fine and seems to be working well, but the slight shipping delay knocked off a star.

FAQS

Stop the installation and contact Philtop customer support. Please provide your vehicle information, order number and photos of the original and received parts so we can help review the fitment.

Alignment may be advisable if suspension or steering components are disturbed during the repair. Follow the vehicle service procedure and check alignment if the vehicle pulls or the steering wheel is off-center.

Noise may come from another wheel bearing, the tire, brake, CV joint, or an installation issue. Recheck the installation and inspect nearby components before assuming the new bearing is faulty.