Fitment: PHILTOP Wheel Hub and Bearing Assembly for 2015-2019 Hyundai Sonata, 2016-2020 Kia Optima, 2016-2021 Hyundai Tucson FWD, 2017-2021 Kia Sportage FWD, 2017-2020 Kia Cadenza, 2019-2022 Hyundai Veloster N.
Wheel Hubs Parameter: Anti Lock Brake Sensor Included :Yes, Bolt Circle Diameter :114.700 mm, Brake Pilot Diameter :76.100 mm, Flange Bolt Hole Quantity :4, Flange Diameter :143.000 mm, Flange Offset :58.900 mm, Hub Pilot Diameter :80.900 mm, Wheel Pilot Diameter :66.800 mm, Wheel Stud Quantity :5.
Long Service Life: Wheel bearing assembly is made of high-quality bearing steel, the parts have the greatest anti-corrosion capacity with fine workmanship and strong bearing capacity.
Excellent Performance: Application-specific advanced raceway design reduces stress, rotation and heat on components.The new wheel hub and bearing assembly restores the vehicle's performance well.
Confirm the vehicle, position, drive type and ABS compatibility.
Compare the mounting holes, splines and sensor configuration with the original part.
Prepare a press or puller and the vehicle-specific torque specifications.
Park on level ground, chock the wheels and support the vehicle with jack stands.
Installation Steps
Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.
After Installation
Rotate the wheel and check for noise, resistance or play.
Confirm proper brake operation and make sure the ABS light is off.
Perform a low-speed road test and check for vibration, steering pull or unusual noise.
Retorque after approximately 100 km when required by the vehicle manufacturer.
Critical Installation Notes
Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
Start Bolts by Hand: Thread bolts two or three turns before using power tools.
Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.
Product Video
Product Description
Reviews
5.0/5
Based on 3 reviews
5
100%
4
0%
3
0%
2
0%
1
0%
V
Valerie P.
01/25/2024
Verified buyer
I had this installed by a mechanic friend, so it's second hand knowledge about the installation process. He said it looks good and is the right part for my 2016 Kia Optima. It's been on a bit now and works fine. If all goes well, I shouldn't need another.
K
Kelly_SUV_Life_486
10/03/2025
Installation was a breeze, everything lined up perfectly. And the shipping was super quick, got it the very next day!
FAQS
Please provide your order number, vehicle information, installation date, current mileage and a description of the issue. Photos, videos or inspection information may also help us review the claim.
Some vehicle manufacturers specify a one-time-use axle nut. Check the service procedure for your vehicle and use new hardware when required.
Torque values differ by vehicle and fastener. Use the vehicle manufacturer’s specification rather than a general value, as incorrect torque may affect bearing operation.
Add your vehicle to ensure fitment
Make
Model
Trim
Engine
Loading vehicle options...
Choose Year, Make, and Model to check exact fitment.
1x Rear Wheel Hub and Bearing Assembly - 512553,Installation Instructions
Bolt Pattern
5 X 4.5
Surface Finish
Polished, Rust Protected
Fitment: PHILTOP Wheel Hub and Bearing Assembly for 2015-2019 Hyundai Sonata, 2016-2020 Kia Optima, 2016-2021 Hyundai Tucson FWD, 2017-2021 Kia Sportage FWD, 2017-2020 Kia Cadenza, 2019-2022 Hyundai Veloster N.
Wheel Hubs Parameter: Anti Lock Brake Sensor Included :Yes, Bolt Circle Diameter :114.700 mm, Brake Pilot Diameter :76.100 mm, Flange Bolt Hole Quantity :4, Flange Diameter :143.000 mm, Flange Offset :58.900 mm, Hub Pilot Diameter :80.900 mm, Wheel Pilot Diameter :66.800 mm, Wheel Stud Quantity :5.
Long Service Life: Wheel bearing assembly is made of high-quality bearing steel, the parts have the greatest anti-corrosion capacity with fine workmanship and strong bearing capacity.
Excellent Performance: Application-specific advanced raceway design reduces stress, rotation and heat on components.The new wheel hub and bearing assembly restores the vehicle's performance well.
5.0
3 reviews
5 star: 3
Compatible Vehicles
Check if this fits your vehicle
Year
Make
Model
Trim
Engine
Notes
2016 - 2017
Hyundai
Sonata
Base
2.4L L4
-
2015 - 2019
Hyundai
Sonata
Eco
1.6L L4
-
2016
Hyundai
Sonata
Hybrid
2.0L L4
-
2016 - 2019
Hyundai
Sonata
Hybrid Limited
2.0L L4
-
2017 - 2019
Hyundai
Sonata
Hybrid SE
2.0L L4
-
2015 - 2019
Hyundai
Sonata
Limited
2.4L L4
-
2015 - 2019
Hyundai
Sonata
Limited 2.0T
2.0L L4
-
2016 - 2019
Hyundai
Sonata
Plug-In Hybrid
2.0L L4
-
2016 - 2019
Hyundai
Sonata
Plug-In Hybrid Limited
2.0L L4
-
2015 - 2019
Hyundai
Sonata
SE
2.4L L4
-
2018 - 2019
Hyundai
Sonata
SEL
2.4L L4
-
2015 - 2019
Hyundai
Sonata
Sport
2.4L L4
-
2015 - 2018
Hyundai
Sonata
Sport 2.0T
2.0L L4
-
2016 - 2017
Hyundai
Tucson
Eco
1.6L L4
Front-Wheel Drive
2016 - 2018
Hyundai
Tucson
Limited
1.6L L4
Front-Wheel Drive
2019 - 2021
Hyundai
Tucson
Limited
2.4L L4
Front-Wheel Drive
2016 - 2021
Hyundai
Tucson
SE
2.0L L4
Front-Wheel Drive
2018
Hyundai
Tucson
SEL
2.0L L4
Front-Wheel Drive
2019 - 2021
Hyundai
Tucson
SEL
2.4L L4
Front-Wheel Drive
2018
Hyundai
Tucson
SEL Plus
2.0L L4
Front-Wheel Drive
2016 - 2017
Hyundai
Tucson
Sport
1.6L L4
Front-Wheel Drive
2018 - 2021
Hyundai
Tucson
Sport
2.4L L4
Front-Wheel Drive
2019 - 2021
Hyundai
Tucson
Ultimate
2.4L L4
Front-Wheel Drive
2017
Hyundai
Tucson
Value
1.6L L4
Front-Wheel Drive
2018
Hyundai
Tucson
Value Edition
1.6L L4
Front-Wheel Drive
2019 - 2021
Hyundai
Tucson
Value Edition
2.0L L4
Front-Wheel Drive
2019
Hyundai
Veloster N
Base
2.0L L4
with ABS Wheel Speed Sensor
2020 - 2022
Hyundai
Veloster N
Base
2.0L L4
-
2017 - 2020
Kia
Cadenza
Limited
3.3L V6
-
2017 - 2019
Kia
Cadenza
Premium
3.3L V6
-
2017 - 2020
Kia
Cadenza
Technology
3.3L V6
-
2019 - 2020
Kia
Optima
EX
1.6L L4
Includes ABS Wheel Speed Sensor
2016 - 2018
Kia
Optima
EX
2.4L L4
Includes ABS Wheel Speed Sensor
2020
Kia
Optima
EX Premium
1.6L L4
Includes ABS Wheel Speed Sensor
2016
Kia
Optima
Hybrid
2.4L L4
Includes ABS Wheel Speed Sensor
2017 - 2020
Kia
Optima
Hybrid EX
2.0L L4
Includes ABS Wheel Speed Sensor
2016
Kia
Optima
Hybrid EX
2.4L L4
Includes ABS Wheel Speed Sensor
2017 - 2018
Kia
Optima
Hybrid Premium
2.0L L4
Includes ABS Wheel Speed Sensor
2016 - 2020
Kia
Optima
LX
2.4L L4
Includes ABS Wheel Speed Sensor
2016 - 2018
Kia
Optima
LX 1.6T
1.6L L4
Includes ABS Wheel Speed Sensor
2017 - 2020
Kia
Optima
Plug-In Hybrid EX
2.0L L4
Includes ABS Wheel Speed Sensor
2018 - 2020
Kia
Optima
S
2.4L L4
Includes ABS Wheel Speed Sensor
2016 - 2020
Kia
Optima
SX
2.0L L4
Includes ABS Wheel Speed Sensor
2016 - 2017
Kia
Optima
SX Limited
2.0L L4
Includes ABS Wheel Speed Sensor
2020
Kia
Optima
Special Edition
2.4L L4
Includes ABS Wheel Speed Sensor
2017 - 2021
Kia
Sportage
EX
2.4L L4
Front-Wheel Drive
2017 - 2021
Kia
Sportage
LX
2.4L L4
Front-Wheel Drive
2020 - 2021
Kia
Sportage
S
2.4L L4
Front-Wheel Drive
2017 - 2021
Kia
Sportage
SX Turbo
2.0L L4
Front-Wheel Drive
Product Specifications
Brand
PHILTOP
ABS Type
Speed Sensor
Lug Count
5
Position
Rear
Flange Bolt Hole Count
4
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
1x Rear Wheel Hub and Bearing Assembly - 512553,Installation Instructions
Confirm the vehicle, position, drive type and ABS compatibility.
Compare the mounting holes, splines and sensor configuration with the original part.
Prepare a press or puller and the vehicle-specific torque specifications.
Park on level ground, chock the wheels and support the vehicle with jack stands.
Installation Steps
Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.
After Installation
Rotate the wheel and check for noise, resistance or play.
Confirm proper brake operation and make sure the ABS light is off.
Perform a low-speed road test and check for vibration, steering pull or unusual noise.
Retorque after approximately 100 km when required by the vehicle manufacturer.
Critical Installation Notes
Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
Start Bolts by Hand: Thread bolts two or three turns before using power tools.
Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.
Product Video
Product Description
Reviews
5.0/5
Based on 3 reviews
5
100%
4
0%
3
0%
2
0%
1
0%
V
Valerie P.
Jan 25,2024
Verified buyer
I had this installed by a mechanic friend, so it's second hand knowledge about the installation process. He said it looks good and is the right part for my 2016 Kia Optima. It's been on a bit now and works fine. If all goes well, I shouldn't need another.
K
Kelly_SUV_Life_486
Oct 03,2025
Installation was a breeze, everything lined up perfectly. And the shipping was super quick, got it the very next day!
FAQS
Please provide your order number, vehicle information, installation date, current mileage and a description of the issue. Photos, videos or inspection information may also help us review the claim.
Some vehicle manufacturers specify a one-time-use axle nut. Check the service procedure for your vehicle and use new hardware when required.
Torque values differ by vehicle and fastener. Use the vehicle manufacturer’s specification rather than a general value, as incorrect torque may affect bearing operation.