2004-2009 Cadillac SRX 3.6L V6 | 2 PC Front AWD Wheel Bearing | OE#12413200/513198 - PHILTOP

2004-2009 Cadillac SRX 3.6L V6 | 2 PC Front AWD Wheel Bearing | OE#12413200/513198 - PHILTOP

Triple-Lip Seal

Front

AWD

4.5

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
9742WBK503XUS

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Drive Type
AWD
Lug Count
6
Position
Front
Flange Bolt Hole Count
3
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Front Wheel Hub and Bearing Assembly - 513198,Installation Instructions
Bolt Pattern
6x4.5
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
3.6 in
Flange Offset
1.66 in/42.1 mm
Flange Diameter
5.73 in/145.5 mm
Brake Pilot Diameter
2.78 in/70.6 mm
Warranty Period
2-Year
OE Number
12413200,7467522,12413106,25998408,12413105
Part Number
513198,HA590078,WE61441,7300375,40262009,BR930363,H513198,FW150,713198,NT513198,104198,102211,40262009E,G513198,141149047,29513198,7467522UR,FW9198
Quantity
2

Highlights

  • [Exact Replacement] 513198 Front Wheel Bearing and Hub Assembly fit for 2004-2009 Cadillac SRX AWD.
  • [Superior Quality] Our wheel bearing hub assembly are made of high quality materials and have the same performance as the original equipment. In addition, the wheel hubs is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • [Long lifespan] Brand new wheel hub assemblies and studs with rust and corrosion protected surface finish, making it has longer bearing life. Better seal design and triple oil seal, which lasts and minimizes noise and vibration and vibration also keeping moisture and other contaminants out.
  • [OE Number] 513198, HA590078, BR930363, 12413200, 12413105, 7467522, 12413106, 25998408, 104198, WE61441, 7300375, 102211, 40262009, 141149047, 29513198, 7467522UR, FW9198, H513198, FW150, 713198, NT513198, 40262009E, G513198
  • [Customer Service] PHILTOP Wheel hub assembly meet OE quality standards and come with a 2 year warranty. If you have any questions about our products, please contact us 24 hours a day.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2004 - 20092004 - 2009
MakeCadillacCadillac
ModelSRXSRX
TrimBaseBase
Engine3.6L V64.6L V8
Note
All-Wheel Drive;Enhanced Hub Assembly - Includes Grime Defense Outboard Seal, Primary Inboard and Outboard Seals, as well as molded grommet for ABS cable
All-Wheel Drive;Enhanced Hub Assembly - Includes Grime Defense Outboard Seal, Primary Inboard and Outboard Seals, as well as molded grommet for ABS cable

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.5/5

Based on 6 reviews

567%
417%
317%
20%
10%

Rob_HomeGarage_688

10/12/2025

The machining on these looks top-notch, and they were a steal price-wise. My Cadillac feels solid on the road again. Great quality for the cost.

Nancy_FirstCar_966

12/21/2025

Got these installed pretty quickly, they fit just right. And the delivery speed was insane, arrived super fast. Big thanks to the seller for the quick turnaround.

FAQS

Stop the installation and contact Philtop customer support. Please provide your vehicle information, order number and photos of the original and received parts so we can help review the fitment.

Torque values differ by vehicle and fastener. Use the vehicle manufacturer’s specification rather than a general value, as incorrect torque may affect bearing operation.

Alignment may be advisable if suspension or steering components are disturbed during the repair. Follow the vehicle service procedure and check alignment if the vehicle pulls or the steering wheel is off-center.