2006-2008 Chevrolet HHR 2.2L/2.4L | 1 PC Front Wheel Bearing 513237 - PHILTOP

2006-2008 Chevrolet HHR 2.2L/2.4L | 1 PC Front Wheel Bearing 513237 - PHILTOP

Triple-Lip Seal

Front

AISI 52100

4.7

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
6625WBR039YUS

Specifications

Brand
PHILTOP
ABS Type
No
Lug Count
5
Position
Front
Flange Bolt Hole Count
3
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
1x Front Wheel Hub and Bearing Assembly - 513237,Installation Instructions
Bolt Pattern
5 X 4.33
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
3.3 in
Wheel Stud Size
M12x1.5
Flange Offset
1.53 in/38.9 mm
Flange Diameter
5.39 in/137.0 mm
Brake Pilot Diameter
2.57 in/65.4 mm
Warranty Period
2-Year
OE Number
12413219,12413220,7467602,22728987
Part Number
513237,HA590087,7300377,WE61017,40062007E,40062007,BR930429,713237,BK1008740L1,NT513237,H513237,951828,124237,102461,7467602UR,PT513237,FW9237,29513237
Quantity
1

Highlights

  • Compatibility: Front Wheel Bearing and Hub Assembly for 2006-2008 HHR.
  • Wheel Hub Num: 513237, HA590087, BR930429, FW299, 22728987, 7300377, 12413220, 12413219, 7467602, 713237, NT513237, BK1008740L1, WE61017, H513237, FW359, WA513237, 40062007E, 102461, 951828, 40062007, FW9237, 29513237, PBR930429, 124237, PT513237, WH513237, 7467602UR.
  • Superior Quality: Our wheel hubs are made of high quality materials and have the same performance as the original equipment. In addition, the wheel bearing hub assembly is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • Recovery Performance: Wheel bearings support the gravity of the entire body and precisely guide the wheel rotation. High-quality wheel hub assemblies allow you to drive your vehicle safely and smoothly.
  • Please Note: If you do not have an installation manual or are not skilled enough to install wheel bearings, it is recommended that you seek assistance from a qualified mechanic.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2006 - 20082007 - 20082006 - 20082006 - 20082007 - 20082007 - 2008
MakeChevroletChevroletChevroletChevroletChevroletChevrolet
ModelHHRHHRHHRHHRHHRHHR
TrimLSLS PanelLTLTLT PanelLT Panel
Engine2.2L L42.2L L42.2L L42.4L L42.2L L42.4L L4
Note
Non-ABS
Non-ABS
Non-ABS
Non-ABS
Non-ABS
Non-ABS

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.7/5

Based on 6 reviews

567%
433%
30%
20%
10%

Amanda_MomOfThree_877

03/18/2026

This hub assembly fixed the wobble I had on my HHR. Now it drives smoothly and quietly. A definite improvement and a good solution to the problem.

DaveTheMechanic_518

11/24/2025

I was impressed by how fast this arrived. It was well-packaged and easy to get installed. Feels like a quality part and a good price.

FAQS

Stop the installation and contact Philtop customer support. Please provide your vehicle information, order number and photos of the original and received parts so we can help review the fitment.

Keep the part clean, avoid impact through the rolling elements, use the correct pressing surface, and tighten fasteners to the specified torque. Professional installation is recommended if special tools are required.

Please do not install the product. Take photos of the item, packaging and shipping label, then contact Philtop customer support as soon as possible for assistance.