2004-2005 Ford F-150 5.4L V8 | 1 PC Front 4WD Wheel Bearing | 4L3Z1104ABFC/515046 - PHILTOP

2004-2005 Ford F-150 5.4L V8 | 1 PC Front 4WD Wheel Bearing | 4L3Z1104ABFC/515046 - PHILTOP

Triple-Lip Seal

Front

4WD

4.0

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
5146WBK288EUS

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Drive Type
4WD
Lug Count
6
Position
Front
Flange Bolt Hole Count
4
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
1x Front Wheel Hub and Bearing Assembly - 515046,Installation Instructions
Bolt Pattern
6 X 5.31
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
3.9 in
Wheel Stud Size
M14x2
Flange Offset
1.79 in/45.5 mm
Flange Diameter
7.2 in/183.0 mm
Brake Pilot Diameter
3.54 in/90.0 mm
Warranty Period
2-Year
OE Number
4L3Z1104ABFC,4L3Z1104AB,4L3Z1104AA,4L342B663AC,4L342B663AE,4L342B663AF,4L342C530AC,4L342B663AG,4L342C530AB
Part Number
515046,7990301,SP550212
Quantity
1

Highlights

  • Fitment: PHILTOP Front Wheel Hub and Bearing Assembly for 2004-2005 Ford F-150 4WD, 2004 Ford F-150 Heritage 4WD.
  • Wheel Hubs Parameter: Anti Lock Brake Sensor Included :Yes, Bolt Circle Diameter :135.000 mm, Brake Pilot Diameter :90.000 mm, Flange Bolt Hole Quantity :4, Flange Diameter :183.000 mm, Flange Offset :45.500 mm, Hub Pilot Diameter :99.300 mm, Spline Quantity :45, Wheel Pilot Diameter :86.800 mm, Wheel Stud Quantity :6.
  • Long Service Life: Wheel bearing assembly is made of high-quality bearing steel, the parts have the greatest anti-corrosion capacity with fine workmanship and strong bearing capacity.
  • Excellent performance: Advanced raceway design for hub bearing applications reduces component stress, rotation and heat. The new hub and bearing assembly restore the vehicle's performance well.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year200420052005200420052005200420052005200420052004200520052004200520042005200420042004200420042004
MakeFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFordFord
ModelF-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150F-150 HeritageF-150 HeritageF-150 HeritageF-150 HeritageF-150 HeritageF-150 Heritage
TrimFX4FX4King RanchLariatLariatSTXSTXSTXXLXLXLXLXLXLTXLTXLTXLTXLTXLXLXLXLTXLTXLT
Engine5.4L V85.4L V85.4L V85.4L V85.4L V84.2L V64.6L V84.6L V84.2L V64.6L V84.6L V85.4L V85.4L V84.2L V64.6L V84.6L V85.4L V85.4L V84.2L V64.6L V85.4L V84.2L V64.6L V85.4L V8
Note
6 Stud
6 Stud;Built Before 11/29/04
6 Stud;Built Before 11/29/04
6 Stud
6 Stud;Built Before 11/29/04
6 Stud;Built Before 11/29/04
6 Stud
6 Stud;Built Before 11/29/04
6 Stud;Built Before 11/29/04
6 Stud
6 Stud;Built Before 11/29/04
6 Stud
6 Stud;Built Before 11/29/04
6 Stud;Built Before 11/29/04
6 Stud
6 Stud;Built Before 11/29/04
6 Stud
6 Stud;Built Before 11/29/04
6 Stud
6 Stud
6 Stud
6 Stud
6 Stud
6 Stud

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.0/5

Based on 2 reviews

50%
4100%
30%
20%
10%

Stacy A.

02/05/2024

Verified buyer

Nice unit that was a direct replacement. Not the easiest to replace, but better than old style bearings.

Customer

01/01/2024

Verified buyer

Easy installationQuality product

FAQS

A single bearing can often be replaced when only one side is worn. The condition of the bearing on the opposite side should also be checked because wear can vary by vehicle and use.

Possible signs include humming or grinding that changes with vehicle speed, wheel looseness, vibration, or an ABS warning. Similar symptoms can have other causes, so an inspection is recommended.

Package contents vary by part number. Please check the product images and specifications to confirm whether the hub, ABS sensor, axle nut, or other hardware is included.