2003-2005 Dodge Ram 2500 5.7L/5.9L/8.0L | 1 PC Front RWD Wheel Bearing | 52010206AB/515089 - PHILTOP

2003-2005 Dodge Ram 2500 5.7L/5.9L/8.0L | 1 PC Front RWD Wheel Bearing | 52010206AB/515089 - PHILTOP

Triple-Lip Seal

Front

RWD

4.7

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
3866WBK599MUS

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Drive Type
RWD
Lug Count
8
Position
Front
Flange Bolt Hole Count
3
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
1x Front Wheel Hub and Bearing Assembly - 515089,Installation Instructions
Bolt Pattern
8x6.5
Surface Finish
Polished, Rust Protected
Flange Diameter
8.07 in/205 mm
Warranty Period
2-Year
OE Number
52010206AB,52010206AA
Part Number
515089,SP550103,7200323,40267014E,40267014,WE61572,BR930475,H515089,715089,NT515089,102021,S0204202178,FW789,HZF421BS3T
Quantity
1

Highlights

  • Compatibility: Wheel Bearing and Hub Assembly for 2003-2005 Ram 2500 RWD, 2003-2005 Ram 3500 RWD
  • Wheel Hub Num: 515089, 52010206AB, 7200323, BR930475, 52010206AA, SP550103, H515089, NT515089, 715089, WE61572, WA515089, 951096, 29515089, WH515089, 40267014E, 102021, MC5201C, 126089, 2306017
  • Superior Quality: Our wheel hubs are made of high quality materials and have the same performance as the original equipment. In addition, the wheel bearing hub assembly is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • Recovery Performance: Wheel bearings support the gravity of the entire body and precisely guide the wheel rotation. High-quality wheel hub assemblies allow you to drive your vehicle safely and smoothly.
  • Please Note: If you do not have an installation manual or are not skilled enough to install wheel bearings, it is recommended that you seek assistance from a qualified mechanic.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year200320052003200520032003 - 20052003 - 200520032003 - 20052003 - 200520032003 - 20052003 - 200520032003 - 20052003 - 200520032003 - 20052003 - 20052003
MakeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodge
ModelRam 2500Ram 2500Ram 2500Ram 2500Ram 2500Ram 2500Ram 2500Ram 2500Ram 2500Ram 2500Ram 2500Ram 3500Ram 3500Ram 3500Ram 3500Ram 3500Ram 3500Ram 3500Ram 3500Ram 3500
TrimLaramieLaramieLaramieLaramieLaramieSLTSLTSLTSTSTSTLaramieLaramieLaramieSLTSLTSLTSTSTST
Engine5.7L V85.7L V85.9L L65.9L L68.0L V105.7L V85.9L L68.0L V105.7L V85.9L L68.0L V105.7L V85.9L L68.0L V105.7L V85.9L L68.0L V105.7L V85.9L L68.0L V10
Note
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.7/5

Based on 6 reviews

583%
40%
317%
20%
10%

Bo

04/24/2025

Verified buyer

Installed this front wheel bearing and hub assembly on my 2004 Dodge Ram 3500 (RWD, 8-lug) and it fit like a glove. The ABS sensor plugged right in with no issues, and the quality of the hub feels solid and well-made.After installation, the annoying humming noise was gone and the truck rides smooth again. The studs are strong, and everything torqued down properly without any fitment problems.

DIY_Karen_298

01/27/2026

No more grinding sounds or wobbling! This hub assembly fixed the problem instantly. My truck feels so much more stable and safe on the road now.

FAQS

Some vehicle manufacturers specify a one-time-use axle nut. Check the service procedure for your vehicle and use new hardware when required.

Unused products may be eligible for return according to the Philtop return policy. Please keep the product and packaging in their original condition and contact us before sending it back.

Installed or modified products may require additional review and may not qualify for a standard return. Please contact Philtop before removing or returning the product.