2009-2010 Ford F-150 5.4L | 2 PC Front 4WD Wheel Bearing | 9L342B6963AB/515119 - PHILTOP

2009-2010 Ford F-150 5.4L | 2 PC Front 4WD Wheel Bearing | 9L342B6963AB/515119 - PHILTOP

Triple-Lip Seal

Front

4WD

4.4

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
3555WBR142BUS

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Drive Type
4WD
Lug Count
6
Position
Front
Flange Bolt Hole Count
4
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Front Wheel Hub and Bearing Assembly - 515119,Installation Instructions
Bolt Pattern
6 X 5.31
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
3.9 in
Wheel Stud Size
M14x2
Flange Offset
1.79 in/45.5 mm
Flange Diameter
7.2 in/183.0 mm
Brake Pilot Diameter
3.54 in/90.0 mm
Warranty Period
2-Year
OE Number
9L342B6963AB,9L3Z1104D,9L3Z1104A
Part Number
515119,SP550214,H515119,BR930759,715119,HUB146,102167,G515119,NT515119
Quantity
2

Highlights

  • [Exact Replacement] 515119 Front Wheel Bearing and Hub Assembly fit for 2009-2010 Ford F-150 4WD
  • [Superior Quality] Our wheel bearing hub assembly are made of high quality materials and have the same performance as the original equipment. In addition, the wheel hubs is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • [Long lifespan] Brand new wheel hub assemblies and studs with rust and corrosion protected surface finish, making it has longer bearing life. Better seal design and triple oil seal, which lasts and minimizes noise and vibration and vibration also keeping moisture and other contaminants out.
  • [OE Number] 515119, SP550214, 9L3Z1104A, 9L342B6963AB, 9L3Z1104D, H515119, BR930759, 715119, HUB146, 102167, G515119, NT515119
  • [Customer Service] PHILTOP Wheel hub assembly meet OE quality standards and come with a 2 year warranty. If you have any questions about our products, please contact us 24 hours a day.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 2010
MakeFordFordFordFordFordFordFordFordFord
ModelF-150F-150F-150F-150F-150F-150F-150F-150F-150
TrimFX4King RanchLariatPlatinumSTXXLXLXLTXLT
Engine5.4L V85.4L V85.4L V85.4L V84.6L V84.6L V85.4L V84.6L V85.4L V8
Note---------

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.4/5

Based on 5 reviews

560%
420%
320%
20%
10%

Steve_DIYer_472

10/24/2025

These feel really heavy duty, the machining looks precise. For the price of two, it's an excellent value. My truck feels much more stable now.

DaveTheMechanic_863

10/10/2025

Bolt-on went smoothly, everything fit perfectly. Shipping was surprisingly quick, got them in just a couple of days. Couldn't ask for more.

FAQS

Check the package contents listed on the product page. If an included item is missing, contact us with your order number and photos of everything received.

Package contents vary by part number. Please check the product images and specifications to confirm whether the hub, ABS sensor, axle nut, or other hardware is included.

A single bearing can often be replaced when only one side is worn. The condition of the bearing on the opposite side should also be checked because wear can vary by vehicle and use.