2009-2010 Dodge Ram 1500 5.7L V8 | 2 PC Front Wheel Bearing | 68024245AA/515126 - PHILTOP

2009-2010 Dodge Ram 1500 5.7L V8 | 2 PC Front Wheel Bearing | 68024245AA/515126 - PHILTOP

Triple-Lip Seal

Front

AISI 52100

4.5

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
6702WBK248GUS

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Lug Count
5
Position
Front
Flange Bolt Hole Count
3
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Front Wheel Hub and Bearing Assembly - 515126,Installation Instructions
Bolt Pattern
5 X 5.5
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
3.5 in
Wheel Stud Size
9/16"x18 Unf
Flange Offset
1.96 in/49.8 mm
Flange Diameter
7.2 in/183.0 mm
Brake Pilot Diameter
3.09 in/78.4 mm
Warranty Period
2-Year
OE Number
68024245AA,52070323AJ,52070323AI
Part Number
515126,HA590354,H515126,BR930808,G515126,102172
Quantity
2

Highlights

  • Fitment: Philtop Front wheel bearing assembly for 1500 2011-2011, R-a-m 1500 2009-2010.
  • OE NUMBER: 515126, 52070323AI, 52070323AJ, 68024245AA, BR930808, HA590354.
  • Quality Bearing Steel: Wheel bearing assemblies are made of high-quality bearing steel with maximum anti-corrosion ability. Fine workmanship, high strength, durable. Philtop wheel bearing assembly can carry the weight well.
  • Precise Structure: Precise roll-form design ensures consistent and optimal preload to minimize excessive noise and wear.It provides precise guidance for the rotation of the hub.
  • Tips: Before purchasing, please use "Suncentautoconfirmedfit" to determine whether the product is suitable for your vehicle.This is necessary.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102009 - 20102011201120112011201120112011201120112011201120112011
MakeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeDodgeRamRamRamRamRamRamRamRamRamRamRamRamRam
ModelRam 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 1500Ram 15001500150015001500150015001500150015001500150015001500
TrimLaramieSLTSLTSTSTSTSportTRXTRXTRX4TRX4Big HornBig HornLaramieLaramie LonghornOutdoorsmanOutdoorsmanSLTSLTSTSTSTSportTradesman
Engine5.7L V84.7L V85.7L V83.7L V64.7L V85.7L V85.7L V84.7L V85.7L V84.7L V85.7L V84.7L V85.7L V85.7L V85.7L V84.7L V85.7L V84.7L V85.7L V83.7L V64.7L V85.7L V85.7L V85.7L V8
Note
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug;From 12/08/2008
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug
5 Lug

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.5/5

Based on 6 reviews

567%
417%
317%
20%
10%

Customer

01/26/2025

Verified buyer

So far so good it is still working!

SarahDrives_84

11/02/2025

Super easy to get these installed. They fit perfectly, and I was up and running in no time. Shipping was fast too!

FAQS

Torque values differ by vehicle and fastener. Use the vehicle manufacturer’s specification rather than a general value, as incorrect torque may affect bearing operation.

Some vehicle manufacturers specify a one-time-use axle nut. Check the service procedure for your vehicle and use new hardware when required.

Alignment may be advisable if suspension or steering components are disturbed during the repair. Follow the vehicle service procedure and check alignment if the vehicle pulls or the steering wheel is off-center.