Kit Includes: 1x Front cv axle shaft - 66-7253. CV axles are designed to work with your vehicle make and model
High Precision Design: CV shafts are manufactured by precision instruments and rigorously tested before sale to make the interface perfectly match your vehicle.The performance of CV shafts is far superior to ordinary types.
Top Quality: CV shafts made of high-quality neoprene rubber and grease ensure that the product stays lubricated, helping to extend the life of the CV shaft.
Easy Installation: CV axles are carefully designed and tested to work perfectly with your vehicle. The installation process ensures an accurate and secure connection.
Confirm the vehicle, installation position, spline counts, mounting points and ABS components match.
Inspect the hub bearing, suspension parts, transmission mount and axle seal. Repair looseness, damage or leakage first.
Compare the new and original axles in a fully compressed position. Confirm the compressed length and key dimensions match.
Check that the boots, clamps, splines and supplied axle nut are complete and undamaged.
Support both CV joints when handling. Do not pull, sharply bend or carry the axle by its rubber boot.
Installation Steps
Step-1: Secure the Vehicle: Loosen the axle nut with the wheels on the ground. Raise the vehicle on a level surface and support it securely with jack stands.
Step-2: Remove the Old Axle: Remove the wheel and necessary suspension components. Separate the outer spline from the hub with the proper puller.
Step-3: Release the Inner Joint: Use a CV joint puller or slide hammer. Never strike the axle directly or pull it out with bolts. Be prepared for possible transmission-fluid loss.
Step-4: Install the New Axle: Clean the splines and seal-contact surface. Insert the inner joint straight into the transmission until the retaining ring fully locks, then install the outer spline into the hub.
Step-5: Reassemble and Torque: Reinstall all suspension components and use a new axle nut. Hand-start the fasteners and tighten everything to the vehicle manufacturer’s specified torque.
Step-6: Final Assembly: Reinstall the wheel, torque the lug nuts in a crisscross pattern and check or refill the specified transmission fluid if required.
After Installation
Confirm the inner joint is fully seated and all fasteners are secure.
Check the CV boots, clamps and axle seal for damage or leakage.
Rotate the wheel by hand and verify the axle moves smoothly without binding or contacting nearby components.
Perform a low-speed road test. Check for clicking while turning, clunking during acceleration, vibration and fluid leakage.
If suspension geometry was disturbed, have the wheel alignment checked.
Product Video
Product Description
Reviews
4.6/5
Based on 9 reviews
5
67%
4
22%
3
11%
2
0%
1
0%
T
tester67
07/29/2026
Verified buyer
For the price, this has been a very good buy. The part fits well, feels sturdy, and installs straightforwardly for the listed application. Exact vehicle fitment and alignment should be verified before putting serious miles on it. Overall, it is a good value and does the job.
D
DaveTheMechanic_411
01/16/2026
The clicking noise on my Beetle is completely gone! This axle solved the problem perfectly. It feels much more stable and smooth now. Very satisfied.
FAQS
Fitment depends on the engine, transmission, and whether your car has ABS. Please enter your vehicle's Brand, Year, and Model into the "Fitment Checker" at the top of the page to confirm a match.
Most CV axles are side-specific due to different lengths. Please check the "Placement on Vehicle" section in our specifications table to ensure you are ordering the correct side for your repair.
The number of teeth (splines) on the ends must match exactly. Please refer to the "Technical Specifications" on this page to verify the Inner and Outer Spline counts before purchasing.
Add your vehicle to ensure fitment
Make
Model
Trim
Engine
Loading vehicle options...
Choose Year, Make, and Model to check exact fitment.
1999-2005 Volkswagen Jetta 1.8L | Front Passenger Side CV Axle Shaft | 667253 - PHILTOP
Kit Includes: 1x Front cv axle shaft - 66-7253. CV axles are designed to work with your vehicle make and model
High Precision Design: CV shafts are manufactured by precision instruments and rigorously tested before sale to make the interface perfectly match your vehicle.The performance of CV shafts is far superior to ordinary types.
Top Quality: CV shafts made of high-quality neoprene rubber and grease ensure that the product stays lubricated, helping to extend the life of the CV shaft.
Easy Installation: CV axles are carefully designed and tested to work perfectly with your vehicle. The installation process ensures an accurate and secure connection.
Confirm the vehicle, installation position, spline counts, mounting points and ABS components match.
Inspect the hub bearing, suspension parts, transmission mount and axle seal. Repair looseness, damage or leakage first.
Compare the new and original axles in a fully compressed position. Confirm the compressed length and key dimensions match.
Check that the boots, clamps, splines and supplied axle nut are complete and undamaged.
Support both CV joints when handling. Do not pull, sharply bend or carry the axle by its rubber boot.
Installation Steps
Step-1: Secure the Vehicle: Loosen the axle nut with the wheels on the ground. Raise the vehicle on a level surface and support it securely with jack stands.
Step-2: Remove the Old Axle: Remove the wheel and necessary suspension components. Separate the outer spline from the hub with the proper puller.
Step-3: Release the Inner Joint: Use a CV joint puller or slide hammer. Never strike the axle directly or pull it out with bolts. Be prepared for possible transmission-fluid loss.
Step-4: Install the New Axle: Clean the splines and seal-contact surface. Insert the inner joint straight into the transmission until the retaining ring fully locks, then install the outer spline into the hub.
Step-5: Reassemble and Torque: Reinstall all suspension components and use a new axle nut. Hand-start the fasteners and tighten everything to the vehicle manufacturer’s specified torque.
Step-6: Final Assembly: Reinstall the wheel, torque the lug nuts in a crisscross pattern and check or refill the specified transmission fluid if required.
After Installation
Confirm the inner joint is fully seated and all fasteners are secure.
Check the CV boots, clamps and axle seal for damage or leakage.
Rotate the wheel by hand and verify the axle moves smoothly without binding or contacting nearby components.
Perform a low-speed road test. Check for clicking while turning, clunking during acceleration, vibration and fluid leakage.
If suspension geometry was disturbed, have the wheel alignment checked.
Product Video
Product Description
Reviews
4.6/5
Based on 9 reviews
5
67%
4
22%
3
11%
2
0%
1
0%
T
tester67
Jul 29,2026
Verified buyer
For the price, this has been a very good buy. The part fits well, feels sturdy, and installs straightforwardly for the listed application. Exact vehicle fitment and alignment should be verified before putting serious miles on it. Overall, it is a good value and does the job.
D
DaveTheMechanic_411
Jan 16,2026
The clicking noise on my Beetle is completely gone! This axle solved the problem perfectly. It feels much more stable and smooth now. Very satisfied.
FAQS
Fitment depends on the engine, transmission, and whether your car has ABS. Please enter your vehicle's Brand, Year, and Model into the "Fitment Checker" at the top of the page to confirm a match.
Most CV axles are side-specific due to different lengths. Please check the "Placement on Vehicle" section in our specifications table to ensure you are ordering the correct side for your repair.
The number of teeth (splines) on the ends must match exactly. Please refer to the "Technical Specifications" on this page to verify the Inner and Outer Spline counts before purchasing.