2006-2015 Lexus IS250 2.5L | 1 PC Front RWD Wheel Bearing | 4356030020/513284 - PHILTOP

2006-2015 Lexus IS250 2.5L | 1 PC Front RWD Wheel Bearing | 4356030020/513284 - PHILTOP

Triple-Lip Seal

Front

RWD

4.8

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
8581WBK5272US

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Drive Type
RWD
Lug Count
5
Position
Front
Flange Bolt Hole Count
4
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
1x Front Wheel Hub and Bearing Assembly - 513284,Installation Instructions
Bolt Pattern
5 X 4.5
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
2.9 in
Wheel Stud Size
M12x1.5
Flange Offset
2.17 in/55 mm
Flange Diameter
5.51 in/139.9 mm
Brake Pilot Diameter
2.44 in/62.0 mm
Warranty Period
2-Year
OE Number
4356030020,4356030011,4356030010
Part Number
513284,HA590138,WE61082,40744031,BR930736,0516398,713284,0516430,3DACF027F9BS,VKBA6954,H513284,WH513284,NT513284,694284,7700034,PT513284,101869,1411248453,40744031E
Quantity
1

Highlights

  • Fitment: Front Left Wheel Bearing Hub Assembly fits RWD IS250 2006-2013, IS350 2006-2010 2014-2015, RWD GS350 2007-2011, RWD GS300 2006, RWD IS350 2011-2013, GS430 2006-2007, IS250 2014-2015, GS450h 2007-2011, GS460 2008-2011.
  • Part Number: 513284, 4356030010, 4356030020, BR930736, HA590138, VKBA6954, 713284, 0516430, 4356030011, H513284.
  • Durable and Long-lasting: Our wheel bearings are made of high-quality materials and are therefore hard, flexible and wear-resistant. This significantly extends the service life of the wheel hub assembly. In addition, the wheel hubs are tested and comply with OE standards.
  • Restoring Vehicle Performance:Replacing the wheel hub bearings with new ones will solve the problem of rattling and wobbling of the vehicle. Our wheel bearing assemblies ensure your driving safety and experience.
  • Installation Advice: Although the wheel bearings conform to the original factory design, it is still recommended that you seek the help of a professional mechanic or refer to a specialized installation manual.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year20062007 - 20112006 - 20072007 - 20112008 - 20112006 - 20132010 - 20132014 - 20152014 - 20152006 - 20132010 - 20132014 - 20152014 - 2015
MakeLexusLexusLexusLexusLexusLexusLexusLexusLexusLexusLexusLexusLexus
ModelGS300GS350GS430GS450hGS460IS250IS250IS250IS250IS350IS350IS350IS350
TrimBaseBaseBaseBaseBaseBaseCCC F SportBaseCCC F Sport
Engine3.0L V63.5L V64.3L V83.5L V64.6L V82.5L V62.5L V62.5L V62.5L V63.5L V63.5L V63.5L V63.5L V6
Note
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
Rear-Wheel Drive
--
Rear-Wheel Drive
Rear-Wheel Drive
--

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.8/5

Based on 5 reviews

580%
420%
30%
20%
10%

Evan Miller

10/19/2025

Verified buyer

Considering the cost, this is a decent bearing that should provide reliable service.

Ali

10/19/2025

Verified buyer

Demonstrates sophisticated engineering solutions that outperform competitors.

FAQS

Installed or modified products may require additional review and may not qualify for a standard return. Please contact Philtop before removing or returning the product.

Warranty coverage and duration may vary by product. For specific warranty period details by product category, please refer to our Warranty & Returns Policy page. Damage related to incorrect fitment, installation or other vehicle problems may require further review.

Please provide your order number, vehicle information, installation date, current mileage and a description of the issue. Photos, videos or inspection information may also help us review the claim.