2009-2012 Chevrolet Colorado 2.9L/3.7L/5.3L | 1 PC Front 4WD Wheel Bearing | 8258321440/515121 - PHILTOP

2009-2012 Chevrolet Colorado 2.9L/3.7L/5.3L | 1 PC Front 4WD Wheel Bearing | 8258321440/515121 - PHILTOP

Triple-Lip Seal

Front

4WD

4.6

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
7104WBK614FUS

Specifications

Brand
PHILTOP
ABS Type
Magnetic Ring
Drive Type
4WD
Lug Count
6
Position
Front
Flange Bolt Hole Count
4
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
1x Front Wheel Hub and Bearing Assembly - 515121,Installation Instructions
Bolt Pattern
6 X 5.5
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
3.3 in
Wheel Stud Size
M12*1.5
Flange Offset
2.65 in/67.3 mm
Flange Diameter
7.24 in/184.0 mm
Brake Pilot Diameter
3.62 in/91.9 mm
Warranty Period
2-Year
OE Number
8258321440,25832144
Part Number
515121,HA590304,H515121,BR930703,NT515121
Quantity
1

Highlights

  • Fitment: Front Wheel Bearing Hub Assembly fits 4WD Colorado 2009-2012, 4WD Canyon 2009-2012.
  • Part Number: BR930703, 515121, BR930164, 25832144, 8258321440, 0516367, HA590304, NT515121, WA515121, 715121, WE61331, H515121, 7300418, WH515121, 40166001E, 29555105, FW348, P515121, 29515121, 40166001, PT515121, 102169, 106511, 1411285210.
  • Durable and Long-lasting: Our wheel bearings are made of high-quality materials and are therefore hard, flexible and wear-resistant. This significantly extends the service life of the wheel hub assembly. In addition, the wheel hubs are tested and comply with OE standards.
  • Restoring Vehicle Performance:Replacing the wheel hub bearings with new ones will solve the problem of rattling and wobbling of the vehicle. Our wheel bearing assemblies ensure your driving safety and experience.
  • Installation Advice: Although the wheel bearings conform to the original factory design, it is still recommended that you seek the help of a professional mechanic or refer to a specialized installation manual.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2009 - 20122009 - 20122009 - 20122009 - 20122009 - 20122009 - 20122009 - 20122009 - 2012200920122009 - 20122009 - 20122009 - 20122009 - 2012
MakeChevroletChevroletChevroletChevroletChevroletGMCGMCGMCGMCGMCGMCGMCGMCGMC
ModelColoradoColoradoColoradoColoradoColoradoCanyonCanyonCanyonCanyonCanyonCanyonCanyonCanyonCanyon
TrimLTLTLTWTWTSLESLESLESLTSLTSLTSLTWTWT
Engine2.9L L43.7L L55.3L V82.9L L43.7L L52.9L L43.7L L55.3L V82.9L L42.9L L43.7L L55.3L V82.9L L43.7L L5
Note
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive
Four-Wheel Drive

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.6/5

Based on 8 reviews

575%
413%
313%
20%
10%

David L.

08/05/2026

Verified buyer

Fit my 2011 Colorado perfect. Less then 1/4 price of local stores.

Brad_AutoParts_183

11/11/2025

Installation was surprisingly easy, all the holes lined up perfectly. And the shipping was super quick, arrived right on time. Couldn't be happier with this purchase.

FAQS

Please provide your order number, vehicle information, installation date, current mileage and a description of the issue. Photos, videos or inspection information may also help us review the claim.

Keep the part clean, avoid impact through the rolling elements, use the correct pressing surface, and tighten fasteners to the specified torque. Professional installation is recommended if special tools are required.

Possible signs include humming or grinding that changes with vehicle speed, wheel looseness, vibration, or an ABS warning. Similar symptoms can have other causes, so an inspection is recommended.