1997-2000 Ford Expedition 4.6L V8/5.4L V8 | 2 PC Front 4WD Wheel Bearing | F75W1104CA/515004 - PHILTOP

1997-2000 Ford Expedition 4.6L V8/5.4L V8 | 2 PC Front 4WD Wheel Bearing | F75W1104CA/515004 - PHILTOP

Triple-Lip Seal

Front

4WD

4.8

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
4411WBR187FUS

Specifications

Brand
PHILTOP
ABS Type
Speed Sensor
Drive Type
4WD
Lug Count
5
Position
Front
Flange Bolt Hole Count
3
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Front Wheel Hub and Bearing Assembly - 515004,Installation Instructions
Bolt Pattern
5x5.3
Surface Finish
Polished, Rust Protected
Flange Diameter
7.13 in/181 mm
Warranty Period
2-Year
OE Number
F75W1104CA,XL1Z1104AE,F75Z1104CA
Part Number
515004,SP550201,7250046,40265003,40265003E,BR930208,715004,H515004,WE60869,NT515004,PBR930379,BTD5145,WH515004,951062,HUB40,FW704,PT515004,13296601,134158,53036008,HZF071BS3T,HA515004,44887
Quantity
2

Highlights

  • Fitment: Front Wheel hub assembly compatible with Expedition 1997-2000 4WD, Navigator 1998-2000 4WD
  • Superior Quality: Our wheel bearing hub assembly are made of high quality materials and have the same performance as the original equipment. In addition, the wheel hubs is vehicle tested to ensure proper fit and excellent performance, thus extending the user's service life.
  • Recovery Performance: PHILTOP hub bearings enables the wheels and attached components to rotate smoothly and keeps the wheel attached to the car. Wheel hub bearing can provide you with a smooth and quiet driving environment, enhancing your driving experience.
  • Installation: Wheel hubs excellent assembly performance, precise overall structure, easy and quick installation.
  • Customer Service: PHILTOP Wheel hub assembly meet OE quality standards and come with a 2 year warranty. If you have any questions about our products, please contact us 24 hours a day.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year1997 - 199920001997 - 199920001997 - 199920001997 - 199920001998 - 2000
MakeFordFordFordFordFordFordFordFordLincoln
ModelExpeditionExpeditionExpeditionExpeditionExpeditionExpeditionExpeditionExpeditionNavigator
TrimEddie BauerEddie BauerEddie BauerEddie BauerXLTXLTXLTXLTBase
Engine4.6L V84.6L V85.4L V85.4L V84.6L V84.6L V85.4L V85.4L V85.4L V8
Note
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive;To 11/29/1999
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive;To 11/29/1999
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive;To 11/29/1999
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive;To 11/29/1999
0.47 inch (12mm) Wheel Bolts;Four-Wheel Drive

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.8/5

Based on 4 reviews

575%
425%
30%
20%
10%

Lisa_CivicDriver_663

12/31/2025

My old hub was shot, causing all sorts of issues. These new ones fixed everything, and the ride quality has improved dramatically. So glad I replaced them.

DIY_Karen_625

02/22/2026

Super easy to install, and they got here way faster than I expected. Everything lined up perfectly. Great for DIYers.

FAQS

Stop the installation and contact Philtop customer support. Please provide your vehicle information, order number and photos of the original and received parts so we can help review the fitment.

The design depends on the application. Compare the product type and images with the original part before installation; press-in bearings generally require suitable shop tools.

Some bearings have a magnetic encoder or sealing side that must face a particular direction. Follow the vehicle service information and any markings supplied with the part.