2002-2004 Toyota Camry 2.4L L4/3.0L V6/3.3L V6 | 2 PC Rear Wheel Bearing | OE#4241033050/512208 - PHILTOP

2002-2004 Toyota Camry 2.4L L4/3.0L V6/3.3L V6 | 2 PC Rear Wheel Bearing | OE#4241033050/512208 - PHILTOP

Triple-Lip Seal

Rear

AISI 52100

4.9

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
8449WBR3541US

Specifications

Brand
PHILTOP
ABS Type
No
Lug Count
5
Position
Rear
Flange Bolt Hole Count
4
Material
SAE 1055 Steel and SAE 52100 Steel
Items Included
2x Rear Wheel Hub and Bearing Assembly - 512208,Installation Instructions
Bolt Pattern
5x4.5
Surface Finish
Polished, Rust Protected
Hub Pilot Diameter
2.9 in
Flange Offset
2.93 in/74.5 mm
Flange Diameter
5.98 in/152.0 mm
Brake Pilot Diameter
2.44 in/62.0 mm
Warranty Period
2-Year
OE Number
4241033050,4241006030,4241006050,4241033060
Part Number
512208,HA596030,7700256,40544006,40544006E,WE60905,BR930232,0516090,40039008,NT512208,H512208,712208,WH512208,PBR930232,HZF489B3B,3DACF026F8E,3PACF026F8E,49BWKH55Y5CP29F,PT512208,RW8208
Quantity
2

Highlights

  • Fitment: Rear Wheel Bearing Hub Assembly fits 2002-2004 Toyota Camry.
  • Note: Select your vehicle's “Year, Make, Model” and click on “Check Fit” to make sure it fits your car, or check the product page instructions to make sure the wheel hub assemblies are an exact match.
  • Durable and Long-lasting: Our wheel bearings are made of high-quality materials and are therefore hard, flexible and wear-resistant. This significantly extends the service life of the wheel hub assembly. In addition, the wheel hubs are tested and comply with OE standards.
  • Restoring Vehicle Performance:Replacing the wheel hub bearings with new ones will solve the problem of rattling and wobbling of the vehicle. Our wheel bearing assemblies ensure your driving safety and experience.
  • Installation Advice: Although the wheel bearings conform to the original factory design, it is still recommended that you seek the help of a professional mechanic or refer to a specialized installation manual.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2002 - 20042002 - 20042002 - 20042002 - 20032004
MakeToyotaToyotaToyotaToyotaToyota
ModelCamryCamryCamryCamryCamry
TrimLELESESESE
Engine2.4L L43.0L V62.4L L43.0L V63.3L V6
Note
Non-ABS
Non-ABS
Non-ABS
Non-ABS
Non-ABS

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the vehicle, position, drive type and ABS compatibility.
  • Compare the mounting holes, splines and sensor configuration with the original part.
  • Prepare a press or puller and the vehicle-specific torque specifications.
  • Park on level ground, chock the wheels and support the vehicle with jack stands.

Installation Steps

  • Step-1: Loosen the Axle Nut:Loosen the axle nut while the vehicle is on the ground, then raise and secure the vehicle.
  • Step-2: Remove the Components:Remove the wheel, brake caliper and rotor. Support the caliper without pulling on the brake hose.
  • Step-3: Remove the Old Bearing:Disconnect the ABS sensor and use the correct puller or press. Do not hammer the bearing or steering knuckle.
  • Step-4: Clean the Mounting Surface:Remove rust, dirt and debris to ensure the new bearing seats correctly.
  • Step-5: Install the New Bearing:Install the ABS encoder in the correct direction and press the bearing evenly into position.
  • Step-6: Reassemble and Torque:Start all bolts by hand, reinstall the components and tighten all fasteners to the OE-specified torque.

After Installation

  • Rotate the wheel and check for noise, resistance or play.
  • Confirm proper brake operation and make sure the ABS light is off.
  • Perform a low-speed road test and check for vibration, steering pull or unusual noise.
  • Retorque after approximately 100 km when required by the vehicle manufacturer.

Critical Installation Notes

  • Use the Correct Pressing Surface: Press on the outer race when installing the bearing into the steering knuckle; press on the inner race when installing it onto the hub.
  • Do Not Use an Impact Wrench for Final Tightening: Complete final tightening with a torque wrench.
  • Replace the Axle Nut: Most self-locking axle nuts are designed for one-time use.
  • Protect the ABS Components: Keep grease and debris away from the magnetic encoder and wheel speed sensor.
  • Start Bolts by Hand: Thread bolts two or three turns before using power tools.
  • Follow OE Torque Specifications: Over-tightening can preload the bearing; under-tightening can cause looseness.

Product Video

Product Description

11

Reviews

4.9/5

Based on 14 reviews

586%
414%
30%
20%
10%

jeni

01/25/2025

Verified buyer

High quality perfect fit.

Jordan

01/09/2025

Verified buyer

This part was a direct fit. The install was not difficult and it completely repaired my issue.

FAQS

Unused products may be eligible for return according to the Philtop return policy. Please keep the product and packaging in their original condition and contact us before sending it back.

Installed or modified products may require additional review and may not qualify for a standard return. Please contact Philtop before removing or returning the product.

Warranty coverage and duration may vary by product. For specific warranty period details by product category, please refer to our Warranty & Returns Policy page. Damage related to incorrect fitment, installation or other vehicle problems may require further review.