2015-2019 Dodge Challenger 3.6L V6 | Rear Drive Shaft | 976987 - PHILTOP

2015-2019 Dodge Challenger 3.6L V6 | Rear Drive Shaft | 976987 - PHILTOP

Rear

Factory-Balanced

Corrosion-Resistant

4.7

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
23ISDSA1897US

Specifications

Brand
PHILTOP
Mounting Type
Cv Joint to Cv Joint
Position
Rear
Fully Extended Length
71.42 in/1814 mm
Fully Compressed Length
69.06 in/1754 mm
Shaft Diameter
Φ73/63.5
Items Included
1x Drive Shaft - 976987
Surface Finish
Painted
Two-Piece Design
Yes
Adjustable Length
Yes
Tube Wall Thickness
0.08 in/2 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
976987

Highlights

  • (Compatible Vehicles): Fits 2015-2019 Dodge Challenger for direct rear axle replacement and a matched driveline fit.
  • OE Reference: OE numbers 986220,52123980AC,52123980AD,52123980AE,52123980AF,68272626AD,68272626AC,68272626AB,68272626AA,52123980AG.
  • (Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 71.42 inch; ③Compressed Shaft Length: 69.06 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ73/63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft
  • (Easy Installation)You get a precision-engineered shaft that bolts directly onto your vehicle with no modifications. You save time and effort on installation. You drive away faster, backed by a design that gives you complete confidence from the start
  • Assurance: Backed by manufacturer warranty and packaged for a straightforward replacement, helping you complete service with confidence.

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year20192015 - 20192015 - 2018
MakeDodgeDodgeDodge
ModelChallengerChallengerChallenger
TrimGTSXTSXT Plus
Engine3.6L V63.6L V63.6L V6
Note---

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.7/5

Based on 3 reviews

567%
433%
30%
20%
10%

Rob_HomeGarage_151

12/01/2025

Came really quickly and was packaged well. Had a question for customer service and they were super helpful and friendly. Great experience overall.

Lisa_CivicDriver_569

03/27/2026

Pretty easy to get installed, fit right into place. Definitely simpler than some other driveshafts I've had to deal with. Solid part.

FAQS

No FAQs have been added for this product yet.