2011-2013 Dodge Durango 3.6L V6 | Rear Drive Shaft | 976983 - PHILTOP

2011-2013 Dodge Durango 3.6L V6 | Rear Drive Shaft | 976983 - PHILTOP

Rear

Factory-Balanced

Corrosion-Resistant

4.8

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
56ISDSA1867US

Specifications

Brand
PHILTOP
Mounting Type
Cv Joint to Cv Joint
Position
Rear
Fully Extended Length
71.89 in/1826 mm
Fully Compressed Length
70.12 in/1781 mm
Shaft Diameter
Φ63.5
Items Included
1x Drive Shaft - 976983
Surface Finish
Painted
Two-Piece Design
Yes
Adjustable Length
Yes
Tube Wall Thickness
0.08 in/2 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
976983

Highlights

  • (Vehicle Fitments)Fits for Dodge 2011-2013 Durango 3.6L RWD
  • (Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 71.89 inch; ③Compressed Shaft Length: 70.12 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft
  • (Reference Number)976983,52123632AA,52123799AB,52123799AA
  • (Attention)①Mounting Type: Ball Cage + Ball Cage; ②Design: Two-Piece; ③Adjustable Length for Custom Fit; ④Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Verified Durability Testing) Fatigue and torque load tests are run on every unit, using conditions that mimic real-world driving, to evaluate long-term performance

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2011 - 20132011 - 2013201120112012 - 20132012 - 2013
MakeDodgeDodgeDodgeDodgeDodgeDodge
ModelDurangoDurangoDurangoDurangoDurangoDurango
TrimCitadelCrewExpressHeatSXTSpecial Service
Engine3.6L V63.6L V63.6L V63.6L V63.6L V63.6L V6
Note
w/ Sales Code DR1 (230 mm Rear Axle)
w/ Sales Code DR1 (230 mm Rear Axle)
w/ Sales Code DR1 (230 mm Rear Axle)
w/ Sales Code DR1 (230 mm Rear Axle)
w/ Sales Code DR1 (230 mm Rear Axle)
w/ Sales Code DR1 (230 mm Rear Axle)

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.8/5

Based on 4 reviews

575%
425%
30%
20%
10%

Jennifer_Auto_945

03/04/2026

Wasn't too difficult to put in, fit like a glove. Seems to be better quality than the stock part I replaced. Happy I chose this one.

Nancy_FirstCar_278

03/27/2026

Looks really good, feels very sturdy and well-made. Considering the price, this is an amazing value. Definitely a great purchase for my Durango.

FAQS

No FAQs have been added for this product yet.