2007-2014 Ford Edge 2.0L/3.5L/3.7L | Rear Drive Shaft | 936846 - PHILTOP

2007-2014 Ford Edge 2.0L/3.5L/3.7L | Rear Drive Shaft | 936846 - PHILTOP

Rear

Factory-Balanced

Corrosion-Resistant

4.8

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
81ISDSA0727US

Specifications

Brand
PHILTOP
Mounting Type
Flange Mount
Position
Rear
Fully Extended Length
82.01 in/2083 mm
Fully Compressed Length
80.04 in/2033 mm
Shaft Diameter
Φ76
Items Included
1x Drive Shaft - 936846
Surface Finish
Painted
Flange Shape
Round + Square
Bolt Hole Quantity
4
Two-Piece Design
Yes
Universal Joint Size
φ25*64
Adjustable Length
Yes
Tube Wall Thickness
0.07 in/1.8 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
936846

Highlights

  • (Vehicle Fitments)Fits for Ford 2007-2014 Edge AWD
  • (Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 82.01 inch; ③Compressed Shaft Length: 80.04 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: φ76; ⑥Shaft Wall Thickness: 0.071 inch; ⑦U-Joint Size: φ25*64; ⑧Length is measured end to end across the entire driveshaft
  • (Reference Number)936846,DT4Z4R602A,7T4Z4R602A
  • (Attention)①Mounting Type: Flange mounting; ②Flange Type: Square Shape + Round Shape; ③Design: Two-Piece; ④Adjustable Length for Custom Fit; ⑤Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Quiet Operation Design) With precision bearings, premium-grade grease, and stringent tolerance oversight, this design helps dampen noise levels during driving

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2012 - 20142008 - 20142012 - 20142007 - 20142012 - 20142007 - 201420072009 - 20102011 - 2014
MakeFordFordFordFordFordFordFordFordFord
ModelEdgeEdgeEdgeEdgeEdgeEdgeEdgeEdgeEdge
TrimLimitedLimitedSESESELSELSEL PlusSportSport
Engine2.0L L43.5L V62.0L L43.5L V62.0L L43.5L V63.5L V63.5L V63.7L V6
Note
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs
Fits Both 2 Piece Or 3 Piece Original Designs

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.8/5

Based on 4 reviews

575%
425%
30%
20%
10%

Ashley_RoadTrip_126

04/14/2026

Installed this yesterday and it was pretty smooth. Bolted right up with no fuss. Way easier than some other aftermarket parts I've dealt with. Feels like it'll last.

RickFixIt_756

10/12/2025

Super quick delivery and the packaging was top-notch. Everything was protected well. I called with a question and the support team was really knowledgeable and polite. A pleasure to deal with.

FAQS

No FAQs have been added for this product yet.