2002-2006 Chevrolet Avalanche 1500 5.3L V8 | Rear Drive Shaft | 936294 - PHILTOP

2002-2006 Chevrolet Avalanche 1500 5.3L V8 | Rear Drive Shaft | 936294 - PHILTOP

Rear

Factory-Balanced

Corrosion-Resistant

4.5

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
42ISDSA0347US

Specifications

Brand
PHILTOP
Mounting Type
Slip Yoke + Universal Joint (U-Joint)
Position
Rear
Fully Extended Length
76.1 in/1933 mm
Fully Compressed Length
76.1 in/1933 mm
Shaft Diameter
Φ90
Items Included
1x Drive Shaft - 936294
Surface Finish
Painted
Output Shaft Spline Count
27-1T
Two-Piece Design
No
Universal Joint Size
Φ28.6*92
Adjustable Length
No
Tube Wall Thickness
0.12 in/3 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
936294

Highlights

  • (Vehicle Fitments)Fits for Chevrolet 2000-2006 Suburban/Avalanche 1500 RWD,for GMC 2000-2006 Yukon XL 1500 RWD
  • (Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 76.10 inch; ③Compressed Shaft Length: 76.10 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ90; ⑥Shaft Wall Thickness: 0.118 inch; ⑦U-Joint Size: Φ28.6*92; ⑧Length is measured end to end across the entire driveshaft
  • (Reference Number)936294,15105506,15051777,15075236,15090206,10390404
  • (Attention)①Mounting Type: Slip Yoke + Universal Joint; ②Adjustable Length for Custom Fit; ③Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Precise Vehicle Fitment) Every drive shaft goes through high-speed dynamic balancing before being packed for shipment. This step helps lower vibration frequency and contributes to more consistent wear across the system

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year2002 - 20052005 - 20062005 - 20062002 - 200320032004 - 20062000 - 200120062000 - 20062000 - 2006200620062000 - 20062000 - 2006
MakeChevroletChevroletChevroletChevroletChevroletChevroletChevroletChevroletChevroletChevroletChevroletGMCGMCGMC
ModelAvalanche 1500Avalanche 1500Avalanche 1500Avalanche 1500Avalanche 1500Avalanche 1500Suburban 1500Suburban 1500Suburban 1500Suburban 1500Suburban 1500Yukon XL 1500Yukon XL 1500Yukon XL 1500
TrimBaseLSLTOn Road EditionWBHZ66BaseBaseLSLTZ71SLSLESLT
Engine5.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V85.3L V8
Note--------------

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.5/5

Based on 8 reviews

563%
425%
313%
20%
10%

Customer

09/01/2026

Verified buyer

Heavy duty and is working great in my Yukon XL

CarGuy_John_853

12/04/2025

Installation was a breeze, much smoother than I expected. It fits perfectly and runs true. A great quality part for a reasonable price.

FAQS

No FAQs have been added for this product yet.