1997-2006 Jeep Wrangler 4.0L L6 | Rear Drive Shaft | 936070 - PHILTOP

1997-2006 Jeep Wrangler 4.0L L6 | Rear Drive Shaft | 936070 - PHILTOP

Rear

Factory-Balanced

Corrosion-Resistant

4.8

Check if this fits your vehicle

Select a vehicle to check this product.

SKU:
66ISDSA0147US

Specifications

Brand
PHILTOP
Mounting Type
Slip Yoke + Universal Joint (U-Joint)
Position
Rear
Fully Extended Length
16.71 in/424.5 mm
Fully Compressed Length
16.71 in/424.5 mm
Shaft Diameter
Φ63.5
Items Included
1x Drive Shaft - 936070
Surface Finish
Painted
Output Shaft Spline Count
27-1T
Two-Piece Design
No
Universal Joint Size
Φ27*81.8
Adjustable Length
No
Tube Wall Thickness
0.08 in/2 mm
Shaft Material
Steel
Warranty Period
2-Year
Part Number
936070

Highlights

  • (Vehicle Fitments)Fits for Jeep 1997-2002 Wrangler/TJ 4.0L Manual(Dana 44 Axle (226 mm Ring Gear), 2003-2006 Wrangler/TJ 4.0L(WheelBase:93.4;Dana 44 Axle 226 mm Ring Gear)
  • (Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 16.71 inch; ③Compressed Shaft Length: 16.71 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦U-Joint Size: Φ27*81.8; ⑧Length is measured end to end across the entire driveshaft
  • (Reference Number)936070,52098787AB,52098787AD,52098787AC
  • (Attention)①Mounting Type: Slip Yoke + Universal Joint; ②Please verify vehicle compatibility via Philtop’s Confirmed Fit Tool and thoroughly read the product description prior to purchase
  • (Precision Dynamic Balancing) Each drive shaft is high-speed dynamically balanced before shipment. This process helps reduce operational vibration and supports even drivetrain wear over time

Compatible Vehicles

Check if this fits your vehicle

Vehicle(s) Fit Information

Year20062003 - 20062005 - 20061997 - 20022003 - 20041997 - 20022003 - 200620022003 - 2006
MakeJeepJeepJeepJeepJeepJeepJeepJeepJeep
ModelWranglerWranglerWranglerWranglerWranglerWranglerWranglerWranglerWrangler
Trim65th Anniversary EditionRubiconSESaharaSaharaSportSportXX
Engine4.0L L64.0L L64.0L L64.0L L64.0L L64.0L L64.0L L64.0L L64.0L L6
Note
w/Sales Code DHN (Command-Trac Part Time 4WD System);w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DHN (Command-Trac Part Time 4WD System);w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DHN (Command-Trac Part Time 4WD System);w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DHN (Command-Trac Part Time 4WD System);w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DHN (Command-Trac Part Time 4WD System);w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))
w/Sales Code DHN (Command-Trac Part Time 4WD System);w/Sales Code DRK (Dana 44 Axle (226 mm Ring Gear))

How to Install?

Installation Manual Download

User manual (PDF)
Download

Checks Before Installation

  • Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
  • Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
  • Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
  • Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
  • Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.

Installation Steps

  • Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
  • Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
  • Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
  • Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
  • Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
  • Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
  • Step-7: Connect the rear flange and hand-start all bolts.
  • Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.

After Installation

  • Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
  • Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
  • Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
  • Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.

Product Description

Drive Shaft AssemblyDrive Shaft Assembly

Reviews

4.8/5

Based on 5 reviews

580%
420%
30%
20%
10%

Brad_AutoParts_560

04/19/2026

Got here quicker than I expected, and it was packaged securely. Had a quick question for support, and they were super helpful and friendly. Great service all around.

Ashley_RoadTrip_828

10/19/2025

Looks fantastic, very robust. I'm super impressed with the quality for what I paid. It's a solid piece of equipment that feels like it'll hold up.

FAQS

No FAQs have been added for this product yet.