
2015-2019 Dodge Charger 5.7L | Rear Drive Shaft | 976991 - PHILTOP
Rear
Factory-Balanced
Corrosion-Resistant
Check if this fits your vehicle
Select a vehicle to check this product.
- SKU:
- 77ISDSA1907US
Specifications
Highlights
Compatible Vehicles
Check if this fits your vehicle
Vehicle(s) Fit Information
| Year | 2015 - 2019 |
|---|---|
| Make | Dodge |
| Model | Charger |
| Trim | Pursuit |
| Engine | 5.7L V8 |
| Note | - |
How to Install?
Installation Manual Download
Checks Before Installation
- Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
- Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
- Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
- Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
- Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.
Installation Steps
- Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
- Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
- Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
- Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
- Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
- Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
- Step-7: Connect the rear flange and hand-start all bolts.
- Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.
After Installation
- Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
- Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
- Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
- Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.
Product Description


Reviews
0.0/5
Based on 0 reviews
0%
0%
0%
0%
0%
No reviews match these filters.
FAQS
No FAQs have been added for this product yet.
Add your vehicle to ensure fitment
Loading vehicle options...
Choose Year, Make, and Model to check exact fitment.
2015-2019 Dodge Charger 5.7L | Rear Drive Shaft | 976991 - PHILTOP
Rear
Factory-Balanced
Corrosion-Resistant
- SKU:
- 77ISDSA1907US
$369.97
Check if this fits your vehicle
Select a vehicle to check this product.
- Mounting Type
- Cv Joint to Cv Joint
- Position
- Rear
- Fully Extended Length
- 71.65 in/1820 mm
- Fully Compressed Length
- 69.69 in/1770 mm
- Shaft Diameter
- Φ73/63.5
- Items Included
- 1x Drive Shaft - 976991
- Surface Finish
- Painted
- Two-Piece Design
- Yes
- (Vehicle Fitments)Fits for Dodge 2015-2019 Charger 5.7L RWD Enforcer/Pursuit.Please verify vehicle compatibility via Philtop's Confirmed Fit Tool and thoroughly read the product description prior to purchase
- (Reference Number)976991,68212030AB,68212030AC,68212030AD,68212030AH,68212030AG,68212030AF,68212030AE
- (Specifications)①Installation Position: Rear Side; ②Extended Shaft Length: 71.65 inch; ③Compressed Shaft Length: 69.69 inch; ④Shaft Material: Steel; ⑤Shaft Diameter: Φ73/63.5; ⑥Shaft Wall Thickness: 0.079 inch; ⑦Length is measured end to end across the entire driveshaft; ⑧Mounting Type: Ball Cage + Ball Cage; ⑨Design: Two-Piece; ⑩Adjustable Length for Custom Fit
- (Easy Installation)Engineered down to the millimeter for your vehicle, this drive shaft bolts on without fuss. Quick installation means less downtime. The thoughtful, user-focused design gives you peace of mind from start to finish
- (Drive with Pleasure)PHILTOP focuses on bringing you a safer, more refined, and more comfortable driving experience Our driveshaft, engineered as an exact OEM replacement, helps restore your vehicle's original performance and driving pleasure
0.0
0 reviews
Compatible Vehicles
Check if this fits your vehicle
| Year | Make | Model | Trim | Engine | Notes |
|---|---|---|---|---|---|
| 2015 - 2019 | Dodge | Charger | Pursuit | 5.7L V8 | - |
Product Specifications
- Brand
- PHILTOP
- Mounting Type
- Cv Joint to Cv Joint
- Position
- Rear
- Fully Extended Length
- 71.65 in/1820 mm
- Fully Compressed Length
- 69.69 in/1770 mm
- Shaft Diameter
- Φ73/63.5
- Items Included
- 1x Drive Shaft - 976991
- Surface Finish
- Painted
- Two-Piece Design
- Yes
- Adjustable Length
- Yes
- Tube Wall Thickness
- 0.08 in/2 mm
- Shaft Material
- Steel
- Warranty Period
- 2-Year
- Part Number
- 976991
How to Install?
Installation Manual Download
Checks Before Installation
- Confirm the driveshaft length, spline count, flange type, mounting pattern and number of sections.
- Inspect the shaft tube, U-joints, splines, center support bearing and rubber cushions for damage or excessive play.
- Measure driveshaft length with the vehicle at normal ride height, not with the suspension hanging freely.
- Support the vehicle securely and keep the transmission and rear axle at approximately the same height.
- Before removal, clearly mark the front and rear orientation, flange positions and section alignment. The driveshaft must not be installed backward.
Installation Steps
- Step-1: Place the transmission in Neutral when rotation is required, secure the wheels and support the driveshaft.
- Step-2: Loosen the rear flange bolts gradually in a diagonal sequence.
- Step-3: Disconnect the rear flange, center support bearing and front connection. Keep the driveshaft supported horizontally.
- Step-4: Cap the transmission and differential openings immediately to prevent fluid leakage and contamination.
- Step-5: Install the front end in the correct direction and align all previously made orientation and phase marks.
- Step-6: Install the center support bearing without twisting or preloading its rubber cushion.
- Step-7: Connect the rear flange and hand-start all bolts.
- Step-8: Use a torque wrench to tighten all flange and support-bearing bolts to the vehicle manufacturer's specified torque. Do not use an impact wrench.
After Installation
- Confirm all phase marks remain aligned and the driveshaft has not been installed front-to-rear.
- Rotate the shaft by hand and check for binding, interference or abnormal joint movement.
- Perform a low-speed road test, then gradually increase speed while checking for noise or vibration.
- Reinspect all fasteners, support bearings and transmission or differential seals after the test drive.
Product Description


Reviews
0.0/5
Based on 0 reviews
0%
0%
0%
0%
0%
No reviews match these filters.
FAQS
No FAQs have been added for this product yet.